Effects of electrostatics and peptide size on peptide interactions with surfacebound microgels were investigated with ellipsometry, confocal microscopy, and atomic force microscopy (AFM). Results show that binding of cationic poly-L-lysine (pLys) to anionic, covalently immobilized, poly(ethyl acrylate-co-methacrylic acid) microgels increased with increasing peptide net charge and microgel charge density. Furthermore, peptide release was facilitated by decreasing either microgel or peptide charge density. Analogously, increasing ionic strength facilitated peptide release for short peptides. As a result of peptide binding, the surface-bound microgels displayed pronounced deswelling and increased mechanical rigidity, the latter quantified by quantitative nanomechanical mapping. While short pLys was found to penetrate the entire microgel network and to result in almost complete charge neutralization, larger peptides were partially excluded from the microgel network, forming an outer peptide layer on the microgels. As a result of this difference, microgel flattening was more influenced by the lower Mw peptide than the higher. Peptide-induced deswelling was found to be lower for higher Mw pLys, the latter effect not observed for the corresponding microgels in the dispersed state. While the effects of electrostatics on peptide loading and release were similar to those observed for dispersed microgels, there were thus considerable effects of the underlying surface on peptide-induced microgel deswelling, which need to be considered in the design of surface-bound microgels as carriers of peptide loads, e.g., in drug delivery or in functionalized biomaterials.

This review presents scientific findings concerning the use of bioactive nanocomposites in the field of tissue repair and regeneration. Bioactivity is the ability of a material to incite a specific biological reaction, usually at the boundary of the material. Nanocomposites have been shown to be ideal bioactive materials due the many biological interfaces and structures operating at the nanoscale. This has resulted in many researchers investigating nanocomposites for use in bioapplications. Nanocomposites encompass a number of different structures, incorporating organic-inorganic, inorganic-inorganic and bioinorganic nanomaterials and based upon ceramic, metallic or polymeric materials. This enables a wide range of properties to be incorporated into nanocomposite materials, such as magnetic properties, MR imaging contrast or drug delivery, and even a combination of these properties. Much of the classical research was focused on bone regeneration, however, recent advances have enabled further use in soft tissue body sites too. Despite recent technological advances, more research is needed to further understand the long-term biocompatibility impact of the use of nanoparticles within the human body.

No abstract

We show that a new type of hydrogel can be prepared by covalently inter-linking binary blends of microgel (MG) particles and that the swelling ratio and modulus of the gels can be predicted from their composition. In previous work we established that physical gels of glycidyl methacrylate (GMA) functionalised poly(methyl methacrylate-co-methacrylic acid-co-ethyleneglycol dimethacrylate) microgel particles (GMA-MG) could be covalently inter-linked to give hydrogels, termed doubly crosslinked microgels, DX MGs. We build on this concept here by investigating the properties of DX MGs containing binary blends of GMA-MG particles and glycidyl oligo(ether ester) acrylate-functionalised microgel particles (GOE-MG). These new hydrogels were assembled by inter-linking nanoscale MG building blocks in the absence of small molecule monomers or crosslinkers. The volume fraction of GMA-MG particles used to prepare the GOE-GMA DX MGs was systematically varied. Rheology data showed that inclusion of GMA-MG and GOE-MG within the GOE-GMA DX MGs increased the modulus and yield strain, respectively, compared to the values measured for the respective physical gels. The data for the covalent GOE-GMA DX MG gels showed that the ductility increased with increasing GOE-MG content. GOE provided covalent inter-linking of the MG particles and also acted as a lubricant between particles due to its low Tg. By demonstrating compositionally determined swelling and mechanical properties for DX MG gels prepared using binary blends of MG particles, this study introduces a new, widely applicable, hydrogel construction assembly concept that is not available for conventional hydrogels.

ABSTRACT:Doubly crosslinked microgels (DX MGs) are hydrogels constructed by covalently interlinked vinyl-functionalised microgel particles. Until now it has not been possible to precisely control the extent of vinyl functionalisation of the microgel (MG) particles which act as the colloidal building blocks for hydrogel assembly. Furthermore, the range of DX MGs prepared to date has been modest. This study addresses both of these challenges by constructing a new class of DX MG using MG particles that were vinyl functionalised by copper catalysed azide-alkyne cycloaddition (CuAAC). Here, poly(2-vinylpyridine-co-propargyl acrylate) (PVP-PA) MG particles were and DX MG mechanical properties, they also showed evidence of colloidal crystallinity which may lead to future photonic gel applications. Our CuAAC-based approach should be versatile and is expected to enable a range of new DX MGs to be prepared.