No abstract

Both open and percutaneous short-segment pedicle fixation were safe and effective methods to treat thoracolumbar burst fractures. Percutaneous fixation without fusion seems to be suitable for type A3 and A4 fractures.

No abstract

Treatment of fractures of the fifth lumbar vertebra depends on fracture type and neurological findings. Conservative management of this condition is appropriate provided there is no neurological damage and canal stenosis and deformity is minimal. Surgical treatment of burst lumbar fractures with neurological deficit is strongly recommended. The optimum treatment remains debatable.

Background. The aim of the experiment was to compare the mechanical properties of intact spinal segment with impaired intervertebral disc and impaired intervertebral disc fixed by TSLP (Thoracolumbar Spine Locking Plate).Methods and results. Spinal specimens were taken from domestic swine. A total of 8 test mechanical states (intact, impaired and fixed) were modeled and the mechanical properties, expressed by the value of moment of couple necessary to twist the specimen at tensile force F = 200 N and the value of moments necessary for extension straining, were determined. The study was based on in vitro biomechanical testing of the TSLP plate used to stabilize the front thoracolumbar column of spinal segments taken from a pig. The plate was used for monosegmental fixation. The disc was cut by scalpel to simulate the Type A injury to front spinal column. In each state (intact, impaired or fixed), specimens were subjected to a tension load of prescribed force and, then, twisted by a given angle. Subsequently, extension load of intact, impaired and impaired & fixed segment was measured. Statistical evaluation verified the hypothesis of the different behavior of intact, impaired and fixed specimens -both for tension & torsion load and extension load. The analyses did not indicate different mechanical behavior of intact and fixed specimens. In other words, monosegmental fixation of both impaired and intact specimens by TSLP Synthes implant will lead to similar mechanical behavior of these specimens. Further, we found that intact and fixed specimens show non-symmetric behavior at positive and negative twisting angles. This was not observed for impaired specimens.Conclusion. Several stabilization systems were developed to stabilize the front thoracolumbar spinal column. Surgery of the anterior column of injured spine should restore the correct position of the spine, ensure decompression of vertebral canal when neural structures are compressed, and stabilize the spine to allow immediate loading and mobilization of the patient. The aim of this study was to compare mechanical properties of intact spinal segment, impaired spinal segment and impaired spinal segment stabilized by TSLP Synthes implant. The problems were solved by experimental modeling using a testing machine that simulated loads for several mechanical states of the spinal segment. Favorable mechanical properties of TSLP Synthes fixator were demonstrated. The experimental results will be used for subsequent computational modeling of the spinal segment in all experimentally solved states.

Aims.A retrospective analysis of patients with thoracolumbar junction fractures who underwent video-assisted thoracoscopic surgery via a minimally invasive approach (minithoracotomy) for reconstruction of the anterior spinal column. Methods. Between 2002 and 2014, a total of 176 patients were treated by this technique. The patients received either posterior stabilization and, at the second stage, the minimally invasive technique via an anterior approach, or the minimally invasive anterior procedure alone. Results. In the anterior procedure, the average operative time was 90 min. (50 to 130 min). Bony fusion without complications was achieved in all patients within a year of surgery. The loss of correction after the anterior procedure with an allograft or titanium cage was up to 2 degrees at two years follow-up. Conclusion. The minimally invasive approach (minithoracotomy up to 6-7 cm) combined with thoracoscopy is an alternative to an exclusively endoscopic technique enabling us to provide safe surgical treatment of the anterior spinal column.

Treatment of the injured lower cervical spine by an anterior operation and plate fixation was successful in achieving bone fusion in almost every patient and was followed by a complication in only a small proportion of our series. Similar results in other reports indicate that this approach is a safe and effective procedure.

Aims. To assess the results of a biomechanical test of cadaveric specimens, comparing 2 methods of fixation of modified Lapidus arthrodesis in combination with arthrodesis of the first metatarsophalangeal joint. Methods. A total of 12 cadaveric specimens were used in the test. Arthrodesis of the first MTP joint was in all patients fixed with a Variable Angle LCP 1st MTP Fusion Plate 2.4/2.7. Two methods of fixation of the Lapidus arthrodesis were compared, i.e. fixation with two screws in the PS (plate-screw) version versus fixation with X-Locking Plate 2.4/2.7 in the PP (plate-plate) version. Measurements were obtained with the use of a testing machine ZWICK Z 020-TND with an optical device Mercury RT for measuring deformities. Each specimen was subjected to 3 loading options, a. displacement 5 mm, the support is placed under the proximal phalanx, b. displacement 5 mm, the support is placed under the first metatarsal head and c. load to failure, the support is placed under the first metatarsal head. Results. In all specimens the PS construct showed a statistically considerably higher stiffness than the PP construct. In all specimens treated with the PP construct the load to failure was lower than in the PS construct. For loading mode a., at a significance level of 0.05 (P<0.05), the P-value was 0.036, for mode b. the P-value was 0.007 and for loading mode c. the P-value was 0.006. In addition, age-related decrease in stiffness of the specimen was proved at a significance level of 5% (P=0.004). Conclusion.In all the three loading modes, the PS (plate-screw) construct showed a statistically higher stiffness than the PP (plate-plate) construct.