A high-temperature, sensible heat thermal energy storage (TES) system is designed for use in a central receiver concentrating solar power plant. Air is used as the heat transfer fluid and solid bricks made out of a high storage density material are used for storage. Experiments were performed using a laboratory-scale TES prototype system, and the results are presented. The air inlet temperature was varied between 300 °C to 600 °C, and the flow rate was varied from 50 cubic feet per minute (CFM) to 90 CFM. It was found that the charging time decreases with increase in mass flow rate. A 1D packed-bed model was used to simulate the thermal performance of the system and was validated with the experimental results. Unsteady 1D energy conservation equations were formulated for combined convection and conduction heat transfer and solved numerically for charging/discharging cycles. Appropriate heat transfer and pressure drop correlations from prior literature were identified. A parametric study was done by varying the bed dimensions, fluid flow rate, particle diameter, and porosity to evaluate the charging/discharging characteristics, overall thermal efficiency, and capacity ratio of the system.
Thermal energy storage for concentrating solar thermal power (CSP) plants can help in overcoming the intermittency of the solar resource and also reduce the levelized cost of energy (LCOE) by utilizing the power block for extended periods of time. In general, heat can be stored in the form of sensible heat, latent heat, and thermochemical reactions. This article describes the development of a costeffective latent heat storage TES at the University of South Florida (USF). Latent heat storage systems have higher energy density compared to sensible heat storage systems. However, most phase change materials (PCMs) have low thermal conductivity that leads to slow charging and discharging rates. The effective thermal conductivity of PCMs can be improved by forming small macrocapsules of PCM and enhancing convective heat transfer by submerging them in a liquid. A novel encapsulation procedure for high-temperature PCMs that can be used for thermal energy storage (TES) systems in CSP plants is being developed at USF. When incorporated in a TES system, these PCMs can reduce the system costs to much lower rates than currently used systems. Economical encapsulation is achieved by using a novel electroless deposition technique. Preliminary results are presented and the factors that are being considered for process optimization are discussed.
The pressure drop of a packed bed thermal energy storage system with irregular shaped solid pellets and tank-toparticle diameter ratio of 10.4 is investigated. The bed height to diameter ratio is 2. The particle sphericity is calculated and used to compare pressure drop correlations to the measured values in the particle Reynolds number range of 353 ≤ Re p ≤ 5206.
As the importance of latent heat thermal energy storage increases for utility scale concentrating solar power (CSP) plants, there lies a need to characterize the thermal properties and melting behavior of phase change materials (PCMs) that are low in cost and high in energy density. In this paper, the results of an investigation of the melting temperature and latent heat of two binary high temperature salt eutectics are presented. Melting point and latent heat are analyzed for a chloride eutectic and carbonate eutectic using simultaneous Differential Scanning Calorimetry (DSC) and Thermogravimetric Analsysis (TGA). High purity materials were used and the handling procedure was carefully controlled to accommodate the hygroscopic nature of the chloride eutectic. The DSC analysis gives the values of thermal properties of the eutectics, which are compared with the calculated (expected/published) values. The thermal stability of the eutectics is also examined by repeated thermal cycling in a DSC and is reported in the paper along with a cost analysis of the salt materials.
The transient behavior of a thermal energy storage system was studied numerically. The storage system is composed of cylindrical tube containing the phase change material (PCM) surrounded by the heat transfer fluid (HTF) that flows along the axial direction of the tube. The melting of PCM was solved using specific heat capacity method. The heat transfer inside the tubes was analyzed by solving the energy equation, which was coupled with the heat conduction equation in the container wall. The velocity profile was obtained by solving the annular flow outside the tubes. The parameters that control the thermal behavior were identified. Several numerical simulations were performed to assess the effects of the Reynolds number on the heat transfer process of the system during the melting of a PCM.
A high temperature sensible heat thermal energy storage (TES) system is designed for use in a central receiver concentrating solar power plant. Air is used as the heat transfer fluid and solid bricks made out of a high storage density material are used for storage. Experiments were performed using a laboratory scale TES prototype system and the results are presented. The air inlet temperature was varied between 300°C to 600°C and the flow rate was varied from 50 CFM to 90 CFM. It was found that the charging time decreases with increase in mass flow rate. A 1D packed bed model was used to simulate the thermal performance of the system and was validated with the experimental results. Unsteady 1D energy conservation equations were formulated for combined convection and conduction heat transfer, and solved numerically for charging/discharging cycles. Appropriate heat transfer and pressure drop correlations from prior literature were identified. A parametric study was done by varying the bed dimensions, fluid flow rate, particle diameter and porosity to evaluate the charging/discharging characteristics, overall thermal efficiency and capacity ratio of the system.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.