New tissue engineering technologies will rely on biomaterials that physically support tissue growth and stimulate specific cell functions. The goal of this study was to create a biomaterial that combines inherent biological properties which can specifically trigger desired cellular responses (e.g., angiogenesis) with electrical properties which have been shown to improve the regeneration of several tissues including bone and nerve. To this end, composites of the biologically active polysaccharide hyaluronic acid (HA) and the electrically conducting polymer polypyrrole (PP) were synthesized and characterized. Electrical conductivity of the composite biomaterial (PP/HA) was measured by a four-point probe technique, scanning electron microscopy was used to characterize surface topography, X-ray photoelectron spectroscopy and reflectance infrared spectroscopy were used to evaluate surface and bulk chemistry, and an assay with biotinylated hyaluronic acid binding protein was used to determine surface HA content. PP/HA materials were also evaluated for in vitro cell compatibility and tissue response in rats. Smooth, conductive, HA-containing PP films were produced; these films retained HA on their surfaces for several days in vitro and promoted vascularization in vivo. PP/HA composite biomaterials are promising candidates for tissue engineering and wound-healing applications that may benefit from both electrical stimulation and enhanced vascularization.

The slow development of cost-effective medical microdevices with strong analytical performance characteristics is due to a lack of selective and efficient analyte capture and signaling. The recently developed programmable bio-nano-chip (PBNC) is a flexible detection device with analytical behavior rivaling established macroscopic methods. The PBNC system employs ≈300 μm-diameter bead sensors composed of agarose “nanonets” that populate a microelectromechanical support structure with integrated microfluidic elements. The beads are an efficient and selective protein-capture medium suitable for the analysis of complex fluid samples. Microscopy and computational studies probe the 3D interior of the beads. The relative contributions that the capture and detection of moieties, analyte size, and bead porosity make to signal distribution and intensity are reported. Agarose pore sizes ranging from 45 to 620 nm are examined and those near 140 nm provide optimal transport characteristics for rapid (<15 min) tests. The system exhibits efficient (99.5%) detection of bead-bound analyte along with low (≈2%) nonspecific immobilization of the detection probe for carcinoembryonic antigen assay. Furthermore, the role analyte dimensions play in signal distribution is explored, and enhanced methods for assay building that consider the unique features of biomarker size are offered.

In most laboratory-scale mammalian cell cultures, the primary mode of oxygen delivery to cultured cells is by passive diffusion through a thin layer of culture medium, and the height of culture medium chosen may therefore have a significant effect on the phenotype of oxygen-sensitive cell types. Many of the liver functions performed by hepatocytes are thought to be regulated into zones by the local oxygen concentration; of particular interest to in vitro toxicologists, the cytochrome P450 family of detoxification enzymes is known to be preferentially expressed by hepatocytes at low (perivenous) oxygen concentrations. Using an array of different medium heights in a 12-well plate format, we show that the height of culture medium has a significant effect on cytochrome P450 1A1 detoxification activity, glucose metabolism, and cell morphology of HepG2 hepatocellular carcinoma cultures. In particular, cytochrome P450 activity exhibits a maximum at medium heights corresponding to perivenous oxygen concentrations. This work demonstrates that optimizing cell culture performance is not always the same as maximizing oxygen delivery.

Porous agarose microbeads, with high surface to volume ratios and high binding densities, are attracting attention as highly sensitive, affordable sensor elements for a variety of high performance bioassays. While such polymer microspheres have been extensively studied and reported on previously and are now moving into real-world clinical practice, very little work has been completed to date to model the convection, diffusion, and binding kinetics of soluble reagents captured within such fibrous networks. Here, we report the development of a three-dimensional computational model and provide the initial evidence for its agreement with experimental outcomes derived from the capture and detection of representative protein and genetic biomolecules in 290μm porous beads. We compare this model to antibody-mediated capture of C-reactive protein and bovine serum albumin, along with hybridization of oligonucleotide sequences to DNA probes. These results suggest that due to the porous interior of the agarose bead, internal analyte transport is both diffusion- and convection-based, and regardless of the nature of analyte, the bead interiors reveal an interesting trickle of convection-driven internal flow. Based on this model, the internal to external flow rate ratio is found to be in the range of 1:3100 to 1:170 for beads with agarose concentration ranging from 0.5% to 8% for the sensor ensembles here studied. Further, both model and experimental evidence suggest that binding kinetics strongly affect analyte distribution of captured reagents within the beads. These findings reveal that high association constants create a steep moving boundary in which unbound analytes are held back at the periphery of the bead sensor. Low association constants create a more shallow moving boundary in which unbound analytes diffuse further into the bead before binding. These models agree with experimental evidence and thus serve as a new tool set for the study of bio-agent transport processes within a new class of medical microdevices.

The majority of microfluidic devices employ networks of channels that have rectangular cross-sections. At the microvascular scale of 30 to 300 microm in diameter, however, the distribution of fluid mechanical stresses and the induced shape of cultured cells will be quite different in a rectangular channel from the near-circular cross-sections seen in vivo. While round-cross-section channels have been produced before by wet etching, fine control of feature size has not been demonstrated, and prior work has only produced channels of a single diameter on a given device. In this work, the xenon difluoride process for isotropic etching of silicon was optimized for production of channels with semicircular cross-sections. This process was then used to produce a network of microvessel-scale semicylindrical channels on a silicon chip, the diameter of which was decreased with each level of branching. Additionally, it was demonstrated that endothelial cells will adhere to both the bottom and sides of these channels, indicating that such chips may be useful in the future for culturing in vitro models of the microvasculature.