On Mars, locally warm surface temperatures (~293 K) occur, leading to the possibility of (transient) liquid water on the surface. However, water exposed to the martian atmosphere will boil, and the sediment transport capacity of such unstable water is not well understood. Here, we present laboratory studies of a newly recognized transport mechanism: “levitation” of saturated sediment bodies on a cushion of vapor released by boiling. Sediment transport where this mechanism is active is about nine times greater than without this effect, reducing the amount of water required to transport comparable sediment volumes by nearly an order of magnitude. Our calculations show that the effect of levitation could persist up to ~48 times longer under reduced martian gravity. Sediment levitation must therefore be considered when evaluating the formation of recent and present-day martian mass wasting features, as much less water may be required to form such features than previously thought.

No abstract

Large outflow channels on ancient terrains of Mars have been interpreted as the products of catastrophic flood events. The rapid burial of water-rich sediments following such flooding could have led to sedimentary volcanism, in which mixtures of sediment and water (mud) erupt to the surface. Tens of thousands of volcano-like landforms populate the northern lowlands and other local sedimentary depocenters on Mars. However, it is difficult to determine whether the edifices are related to igneous or mud extrusions, partly because the behaviour of extruded mud under martian surface conditions is poorly constrained. Here, we investigate the mechanisms of mud propagation on Mars using experiments performed inside a low-pressure chamber at cold temperatures. We find that low viscosity mud under martian conditions propagates differently from on Earth, because of rapid freezing and the formation of an icy crust. Instead, the experimental mud flows propagate like terrestrial pahoehoe lava flows, with liquid mud spilling from ruptures in the frozen crust, then refreezing to form a new flow lobe. We suggest that mud volcanism can explain the formation of some lava-like flow morphologies on Mars, and that similar processes may apply to cryovolcanic extrusions on icy bodies in the Solar System. The physics behind igneous volcanism on Mars is better understood [e.g., 1-4] than that of sedimentary volcanism in which mixtures of water and sediment, subsequently referred to as mud, are extruded onto the surface. On Earth, sedimentary volcanism manifests at the surface as eruptions of fluids (water, gas, occasionally oil), fine grained sediments (e.g. clays) and clasts from the country-rock. These geological phenomena are the result of fluid (on Earth typically associated with methane) overpressure [5], generated at several hundred to several thousand metres depth, combined with gravitational instability of buoyant sedimentary units buried at deeper stratigraphic levels [6]. The viscosity of ascending mud varies, and affects the shapes, sizes and thicknesses of resulting flows. The higher the water

Gullies are widespread morphological features on Mars for which current changes have been observed. Liquid water has been one of the potential mechanisms to explain their formation and activity. However, under present-day Martian conditions, liquid water is unstable and should only be transiently present in small amounts at the surface. Yet little attention has been paid to the mechanisms by which unstable water transports sediment under low atmospheric pressure. Here we present the results of laboratory experiments studying the interaction between liquid water flowing over a sand bed under Mars-like atmospheric pressure (c. 9 mbar). The experiments were performed in a Mars Simulation Chamber (at the Open University, UK), in which we placed a test bed of fine sand at a 25°slope. We chose to investigate the influence of two parameters: the temperature of the water and the temperature of the sand. We performed 27 experiments with nine different combinations of water and sand temperatures ranging from 278 to 297 K. Under all experimental conditions, the water was boiling. We investigated and compared the types and timing of sediment transport events, and the shapes, characteristics and volumes of the resulting morphologies. In agreement with previous laboratory studies we found that more intense boiling increased the volume of sediment transported for a given volume of water. We found four main types of sediment transport: entrainment by overland flow; grain ejection; grain avalanches; and levitation of saturated sand pellets. Our results showed that increasing sand temperature was the main driving parameter in increasing the sand transport and in modifying the dominant sediment transport mechanism. The temperature of the water played a negligible or minor role, apart from the duration of sand ejection and avalanches, which lasted longer at low water temperature. At low sand temperature the majority of the sand was transported by overland flow of the liquid water. At higher sand temperatures the transport was dominated by processes triggered by the boiling behaviour of the water. At the highest temperatures, sediment transport was dominated by the formation of levitating pellets, dry avalanches and ejection of the sand grains. This resulted in a transport volume about nine times greater at a sand temperature of 297 K compared with 278 K. Our heat transfer scaling shows that the boiling behaviour will be enhanced under Martian low gravity, resulting in more efficient transport of sediment by levitating sand pellets even at temperatures close to the triple point. Our results showed that the boiling intensity played an important role in the physics of sediment transport by liquid water. This implied that the amount of water required to produce morphological changes at the surface of Mars could be lower than previously estimated by assuming stable liquid water. Boiling is a critical process to be considered when assessing gully formation and modification mechanisms mobilized by liquid water. Our work could ha...

No abstract

In this study we report about the first in‐situ analysis of terrestrial dust devil tracks (DDTs) observed in the Turpan depression desert in northwestern China. Passages of active dust devils remove a thin layer of fine grained material (< ∼63 μm), cleaning the upper surface of coarse sands (0.5–1 mm). This erosional process changes the photometric properties of the upper surface causing the albedo differences within the track to the surroundings. Measurements imply that a removal of an equivalent layer thickness of ∼2 μm is sufficient to form the dark dust devil tracks. Our terrestrial results are in agreement with the mechanism proposed by Greeley et al. (2005) for the formation of DDTs on Mars.

No abstract

During a field campaign in the Sahara Desert in southern Morocco, spring 2012, we sampled the vertical grain size distribution of two active dust devils that exhibited different dimensions and intensities. With these in situ samples of grains in the vortices, it was possible to derive detailed vertical grain size distributions and measurements of the lifted relative particle load. Measurements of the two dust devils show that the majority of all lifted particles were only lifted within the first meter (∼46.5% and ∼61% of all particles; ∼76.5 wt % and ∼89 wt % of the relative particle load). Furthermore, ∼69% and ∼82% of all lifted sand grains occurred in the first meter of the dust devils, indicating the occurrence of “sand skirts.” Both sampled dust devils were relatively small (∼15 m and ∼4–5 m in diameter) compared to dust devils in surrounding regions; nevertheless, measurements show that ∼58.5% to 73.5% of all lifted particles were small enough to go into suspension (<31 μm, depending on the used grain size classification). This relatively high amount represents only ∼0.05 to 0.15 wt % of the lifted particle load. Larger dust devils probably entrain larger amounts of fine-grained material into the atmosphere, which can have an influence on the climate. Furthermore, our results indicate that the composition of the surface, on which the dust devils evolved, also had an influence on the particle load composition of the dust devil vortices. The internal particle load structure of both sampled dust devils was comparable related to their vertical grain size distribution and relative particle load, although both dust devils differed in their dimensions and intensities. A general trend of decreasing grain sizes with height was also detected.