This paper presents the results of investigations of temperature field distribution in the cutting edge and yield strength of tool material for low-alloy high-speed steels. Investigations of temperature distribution in cutting edges were made during C60 steel turning using a semi-natural constantan thermo-element. The obtained results show that the decrease in addition alloy content does not influence the change in thermal-physical properties of lowalloy high-speed steels. Investigations of the durability of cutting edges confirm that to define working conditions of the tool made of high-speed steel, resistance against hardness loss with increasing temperature at temperatures higher and lower than tempering temperature is the most significant. The results of durability investigations of cutters made of HS3-1-2 steel with various kinds of surface treatment confirm the reasons for cutting edge wear of tools made of high-speed steel and ways of the increasing their durability.
In this paper, the wear mechanism of punches made of M3:2 and M2 steel sheet which are used in blanking process of the rotor part of the low-power asynchronous motor was presented. The influence of additional TiN coating on the punch flank surface degradation intensity was described. The punch wear influence on the hardness changes close the material intersection surface was determined. The research results indicate that the tool durability ensures the quality of parts blanked from electrotechnical steel. The results will allow for selection of new tools materials for this type of tools which are used in difficult tribological conditions.
W procesie eksploatacji przeciągacz podlega wielokrotnemu ostrzeniu. Resurs pracy ostrzonego narzędzia stanowi od 75÷85% okresu pracy przeciągacza. W pracy przeprowadzono analizę efektywności pracy przeciągacza w okresie całego cyklu jego pracy. Badania prowadzono przy obróbce stali C45. Na podstawie otrzymanych wyników badań i ich analizy otrzymano zależność matematyczną wpływu liczby ostrzeń prowadzonych na powierzchni natarcia na uśrednioną wielkość zużycia zębów przeciągacza VB. SŁOWA KLUCZOWE: przeciąganie, zużycie ostrza, rozrzut trwałości, kryterium zużycia, ostrzenie narzędziIn the process of the operation the pull broach is subjected to multiple sharpening. Service life of a sharpened tool is ranged from 75 to 85% of pull broach operation life. In the paper the analysis of efficiency of the pull broach operation in the whole cycle of their operation is presented. The investigations were carried out at machining of C45 steel. The mathematical relationship of the effect of the number of sharpenings conducted on the rake face on the average amount of pull broach tooth wear VB was obtained on the basis of the results of the research and their analysis. KEYWORDS: pull broaching, blade wear, durability dispersion, wear criterion, tools sharpening Przy organizacji procesów skrawania w zautomatyzowanym systemie wytwarzania najbardziej złożone problemy pojawiają się przy ocenie wydajności i niezawodności obróbki. Wysokie wymagania odnośnie jakości obrabianych części determinują technologiczne uszkodzenia jako głów-ny obiekt badań w teorii niezawodności systemu technologicznego [1÷3]. Podczas eksploatacji, system technologiczny podlega oddziaływaniom mechanicznym i cieplnym, które powodują uszkodzenia i zmieniają wartości parametrów jego stanu wyjściowego. Funkcjonowanie wszystkich elementów systemu technologicznego zapewnia realizację procesu technologicznego, ale wskaźniki jakościowe obrabianych części określa w zasadzie oprzyrządowanie technologiczne, obrabiarka i narzędzie. Przy optymalnych warunkach eksploatacji narzędzia mającego wymagane parametry wyjściowe, dominującym czynnikiem są uszkodzenia spowodowane zużyciem powierzchni skrawających narzędzia [4,5]. Aktualnie duża liczba prac jest poświęcona problematyce prognozowania trwałości narzędzi skrawają-cych, w tym i przeciągaczy, koniecznych do opracowania systemu automatycznego projektowania narzędzi [6,7]. Jednak do tej pory wyznaczenie efektywności pracy narzę-dzi pozostaje złożonym i bardzo aktualnym zagadnieniem. Metodyka badańBadania dynamiki zużycia przeciągaczy prowadzono w warunkach produkcyjnych podczas przeciągania wielowypustu o zarysie prostokątnym przedstawionym na rys. 1, na przeciągarce poziomej 7B 510 kompletem przeciągaczy ze stali HS 18-0-1. Materiałem obrabianym był półwyrób ze stali C45 (HB = 260-320) o długości 130 mm.Rys. 1. Rysunek części z obrabianym zarysem wielowypustu Na rys. 2 i w tabl. 1 przedstawiono parametry części skrawającej przeciągacza wykańczającego, dla którego prowadzono badania. Badanie dynamiki zużycia przecią-gac...
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.