No abstract

No abstract

No abstract

The 8-mm diameter bars of Cu-Al-Mn shape memory alloys were produced by continuous casting technique. The samples were characterised using optical microscopy and scanning electron microscopy along with EDX analysis. The continuous cast alloy revealed some martensitic phase, which, after quenching, led to the microstructure that is completely martensite. Quenching of samples had an effect on several mechanical properties and change in morphology of fracture. After ageing at 200 °C and 300 °C, the tensile strength increased and elongation drastically decreased. Morphology of fracture surface changed from primary ductile to a mixture of intergranular and ductile.

The paper presents comparison of microstructure and fracture surface morphology of the CuAlNi shape memory alloy (SMA) after different heat treatment procedures. The investigation was performed on samples in as-cast state and heat treated states (solution annealing at temperatures of 850 °C / 60’ / H2O and 920 °C / 60’ / H2O along with tempering at two different temperature 150 °C / 60’ / H2O and 300 °C / 60’ / H2O). The microstructure of the samples was examined by optical (OM) and scanning electron microscope (SEM) equipped with device for EDS analysis. The obtained fracture surfaces were examined by SEM. Optical and scanning electron microscopy showed martensitic microstructure in all investigated samples. However, the fractographic analysis of samples after tensile testing reveals significant changes in fracture mechanism. In both solution annealed states the results shows transgranular type of fracture, but after tempering at two different temperatures the difference is obvious. After tempering at 150 °C, along with transgranular type of fracture appear some areas with intergranular type of fracture. After tempering at 300 °C, fracture surface reveals completely intergranular type of fracture.

No abstract

In this paper, the microstructure of Cu82.3Al8.3Mn9.4 (in wt. %) shape memory alloy after hot and cold rolling was investigated. The Cu82.3Al8.3Mn9.4 alloy was produced by a vertical continuous casting method in the form a cylinder rod of 8 mm in diameter. After the casting, hot and cold rolling was performed. By hot rolling a strip with a thickness of 1.75 mm was obtained, while by cold rolling a strip with a thickness of 1.02 mm was produced. After the rolling process, heat treatment was performed.Heat treatment was carried out by solution annealing at 900 °C held for 30 minutes and water quenched immediately after heating. The microstructure characterization of the investigated alloy was carried out by optical microscopy (OM), scanning electron microscopy (SEM) equipped with a device for energy dispersive spectroscopy (EDS). Phase transformation temperatures and fusion enthalpies were determined by differential scanning calorimetry (DSC) method. The homogenous martensite microstructure was confirmed by OM and SEM micrographs after casting. During rolling the two-phase microstructure occurred. Results of DSC analysis showed martensite start (Ms), martensite finish (M f ), austenite start (A s ) and austenite finish (A f ) temperatures.

This paper presents the results of thermal and microstructural analysis of Cu-Al-Ni shape memory alloy before and after heat treatment. After casting, a bar of Cu-12.8 Al-4.1 Ni (wt.%) alloy, obtained by the vertical continuous casting technique, was subjected to a certain heat treatment procedure. Solution annealing was performed at 850 °C for 60 min, followed by water quenching. Tempering was then performed at four different temperatures (150 °C, 200 °C, 250 °C and 300 °C). The microstructural results were obtained by optical and scanning electron microscopy. Thermodynamic calculation of ternary Cu-Al-Ni system under equilibrium was performed using Thermo-Calc 5 software. Phase transformation temperatures were determined by differential scanning calorimetry (DSC). The DSC results show the highest values of transformation temperatures in as-cast state. After solution annealing and tempering, the transformation temperatures show lower values with exceptional stability of Ms temperature (martensite start temperature).