Chlorhexidine reduces the TS counts in TTBPE, but has no effect on biofilm mass.

No abstract

Objective: To determine and compare the longitudinal and transverse roughness parameters of the enamel surface of bovine teeth and evaluate the influence of these parameters on bond strength. Materials and Methods: Ninety bovine incisors were used. The surface roughness of enamel was measured with a profilometer. For each tooth, five readings were taken in the longitudinal plane and five were taken in the transverse plane of the long axis of the tooth in an area equal to the size of the bracket base. The metal brackets were bonded with Transbond XT, and bond strength was evaluated in a universal test machine.Results: There was a statistical correlation (P , .01) between the longitudinal and transverse roughness measurements. There was no correlation between roughness measurements (longitudinal and transverse) and bond strength (P . .05), nor was there a correlation between total roughness (longitudinal Ra and transverse Ra) and bond strength. The Student's t-test showed that there was a statistically significant difference (P , .05) between longitudinal and transverse roughness. Conclusion: The transverse roughness is greater than the longitudinal roughness, there is a strong correlation between longitudinal and transverse roughness, and there is no correlation between enamel roughness and bond strength. (Angle Orthod. 2010;80:562-569.)

Objective: In orthodontic treatment, intrusion movement of maxillary incisors is often necessary. Therefore, the objective of this investigation is to evaluate the initial distribution patterns and magnitude of compressive stress in the periodontal ligament (PDL) in a simulation of orthodontic intrusion of maxillary incisors, considering the points of force application. Methods: Anatomic 3D models reconstructed from cone-beam computed tomography scans were used to simulate maxillary incisors intrusion loading. The points of force application selected were: centered between central incisors brackets (LOAD 1); bilaterally between the brackets of central and lateral incisors (LOAD 2); bilaterally distal to the brackets of lateral incisors (LOAD 3); bilaterally 7 mm distal to the center of brackets of lateral incisors (LOAD 4). Results and Conclusions: Stress concentrated at the PDL apex region, irrespective of the point of orthodontic force application. The four load models showed distinct contour plots and compressive stress values over the midsagittal reference line. The contour plots of central and lateral incisors were not similar in the same load model. LOAD 3 resulted in more balanced compressive stress distribution.

BackgroundThis study aimed to simulate the actions of low-pull (LP), high-pull (HP), and combined pull (CP) headgears (HGs) and to analyze tooth movement tendencies through finite element analysis.MethodsTomographic slices of a human maxilla with complete permanent dentition were processed by reconstruction software, and the triangular surface mesh was converted into non-uniform rational B-spline (NURBS) curves. An HG facial bow was also modulated in 3D. The teeth and bone were considered to have isotropic and linear behavior, whereas the periodontal ligament was considered to have non-linear and hyperelastic behavior. Data regarding the application points, directions and magnitudes of forces were obtained from the literature and from a dolichofacial patient with class II, division 1 malocclusion, who was treated with a CP HG.ResultsThe CP HG promoted 37.1 to 41.1 %, and the HP HG promoted 19.1 to 31.9 % of LP distalization. The HP HG presented the highest intrusion, and the LP HG presented the highest extrusion of the first molar. The LP HG contracted the distal side, and the HP and CP HGs contracted the lingual and distobuccal roots of the second molar to a lesser degree.ConclusionsThe LP HG promotes the greatest distalization, followed by the CP and HP HGs; the LP HG causes greater extrusion of the first molar, and the HP HG causes greater intrusion of the first molar. The LP HG causes greater contraction of the second molar than the HP HG.

The aim of this study was to assess the influence of etching and light-curing time on the shear bond strength (SBS) and adhesive remnant index (ARI) of a resin-modified glass ionomer cement (RMGIC) upon debonding of orthodontic brackets. Sixty-eight bovine permanent incisors were obtained and embedded in acrylic resin. Edgewise metallic brackets were bonded to the teeth with Fuji Ortho LC RMGIC. The specimens were randomly assigned to 4 groups, using the following etching and light-curing times: G1: 10% polyacrylic acid and 40 s (control); G2: 37% phosphoric acid and 40 s; G3: 10% polyacrylic acid and 50 s; and G4: 37% phosphoric acid and 50 s. Shear test was performed at 0.5 mm/min and the ARI was assessed. G2 (3.6 ± 0.98 MPa) presented significantly higher (p<0.05) SBS than G1 (2.76 ± 0.86 MPa) and G4 (2.86 ± 0.68 MPa), and there was no statistically significant difference (p>0.05) between G2 and G3 (2.94 ± 0.67 MPa). ARI presented prevalence of scores 2 and 3 in all groups. RMGIC SBS enhanced with 37% phosphoric acid etching and 40 s light-curing time, but this did not occur when the light-curing time was increased, regardless of the acid used. RMGIC presented prevalence of failures at the adhesive/bracket interface.

This study aimed to evaluate biomechanical behaviour of inclined orthodontic mini-implants by analyzing its insertion torque (IT), axial pull-out strength (APS), and cortical bone thickness in contact with mini-implant (CBTC). A total of 102 mini-implants were inserted at 90 degree, 60 degree, and 45 degree to the surface of synthetic bone. Peak IT was measured, and the mini-implants were aligned with the mechanical testing machine to record the APS. The cortical bone thickness in contact with each mini-implant was measured after the pull-out test and the data were subjected to statistical analyses. The 45 degree group had a significantly higher IT compared with the 90 degree group (P < 0.05). There was a statistically significant increase in the average of cortical bone thickness in CBTC across the three groups (P < 0.05). A negative correlation between the angulation and the CBTC (r = -0.95, P < 0.05) and a positive correlation between the APS and the CBTC were observed (r = 0.34, P < 0.05). Mini-implants that are inserted more inclined to the surface of the bone provide greater IT and an increased contact with the cortical bone. The greater the CBTC, the greater is the APS.

No abstract