No abstract

No abstract

In recent years, the addition of carbon nanotubes to construction materials has attracted considerable interest, due to the improvement of mechanical, electrical, and thermal properties of cement. The incorporation of carbon nanotubes into a cement matrix causes an increase of several mechanical properties of up to 170% even with low carbon nanotubes concentrations. The objective of this study is to analyze the influence of the type of functionalization and number of walls of carbon nanotubes on the interaction between these nanostructures and a cement surface and thus, on the improvement of their mechanical properties. Thus, single-walled and double-walled carbon nanotubes were used to investigate the influence of the number of walls. The effect of carbon nanotube functionalization was studied using carbon nanotubes functionalized with carboxyl and carboxylate groups. The experimental results demonstrate that the incorporation of carbon nanotubes into the cement matrix improves the mechanical properties of the resulting material. Functionalized carbon nanotubes perform better than pristine carbon nanotubes. Electrostatic attractions play a central role in establishing strong interactions between the carbon nanotubes and the cement surface. The presence of neutral polar groups on the carbon nanotube surface also improves this interaction. The number of walls seems to be less important.

A series of carbon nanotubes doped with Fe and/or Cu, Fe100−xCux/CNT (x = 0, 25, 50, 75 and 100) has been prepared by an easy method of wetness impregnation of commercial multiwalled carbon nanotubes previously oxidized with nitric acid. The wide characterization of the solids by different techniques demonstrates that the incorporation of Fe and Cu to the CNTs has been successfully produced. Fe100−xCux/CNT samples were tested as catalysts in the removal of paracetamol from aqueous solution by a combined process of adsorption and Fenton-like oxidation. Under mild conditions, 25 °C and natural pH of solution, i.e., nearly neutral, values of oxidation of paracetamol between 90.2% and 98.3% were achieved after 5 h of reaction in most of cases. Furthermore, with the samples containing higher amounts of copper, i.e., Cu100/CNT and Fe25Cu75/CNT, only 2 h were necessary to produce depletion values of 73.2% and 87.8%, respectively. The influence of pH and dosage of H2O2 on the performance has also been studied. A synergic effect between both Cu+/Cu2+ and Fe2+/Fe3+ in Fenton-like reaction was observed. These results demonstrate that Fe100−xCux/CNT are powerful Fenton-like catalyst for degradation of paracetamol from aqueous solution and they could be extended to the removal of other organic pollutants.

Over the last few years, the addition of small amounts of carbon nanotubes (CNTs) to construction materials has become of great interest, since it enhances some of the mechanical, electrical and thermal properties of the cement. In this sense, single-walled and multi-walled carbon nanotubes (SWCNTs and MWCNTs, respectively) can be incorporated into cement to achieve the above-mentioned improved features. Thus, the current study presents the results of the addition of SWCNTs and MWCNTs on the microstructure and the physical properties of the cement paste. Density was measured through He pycnometry and the mass change was studied by thermogravimetric analysis (TGA). The microstructure and the phases were analyzed using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Finally, the electrical conductivity for different CNT concentrations was measured, and an exponential increase of the conductivity with concentration was observed. This last result opens the possibility for these materials to be used in a high variety of fields, such as space intelligent systems with novel electrical and electronic applications.

No abstract

The excessive use of antibiotics has contributed to the rise in antibiotic-resistant bacteria, and thus, new antibacterial compounds must be developed. Composite materials based on graphene and its derivatives doped with metallic and metallic oxide nanoparticles, particularly Ag, Cu, and Cu oxides, hold great promise. These materials are often modified with polyethylene glycol (PEG) to improve their pharmacokinetic behavior and their solubility in biological media. In this work, we performed molecular dynamics (MD) simulations to study the interaction between small Ag, Cu, and CuO clusters and several graphene-based materials. These materials include pristine graphene (PG) and pristine graphene nanoplatelets (PGN) as well as PEGylated graphene oxide (GO_PEG) and PEGylated graphene oxide nanoplatelets (GO-PEG_N). We calculated the adsorption energies, mean equilibrium distances between the nanoparticles and graphene surfaces, and mean square displacement (MSD) of the nanoclusters. The results show that PEGylation favors the adsorption of the clusters on the graphene surfaces, causing an increase in adsorption energies and a decrease in both distances and MSD values. The strengthening of the interaction could be crucial to obtain effective antibacterial compounds.

No abstract