Due to their mechanical and structural similarity to native tissues, hydrogel biomaterials have gained tremendous popularity for applications in 3D tissue culture, therapeutic screening, disease modeling, and regenerative medicine. Recent advances in pre‐ and post‐synthetic processing have afforded anisotropic manipulation of the biochemical, mechanical, and topographical properties of biocompatible gels, increasingly in a dynamic and heterogeneous fashion that mimics natural processes in vivo. Herein, the current state of hydrogel surface patterning to investigate cellular interactions with the surrounding matrix is reviewed, both in techniques utilized and biological findings explored, and the perspective on proposed future directions for the field is offered.
Stimuli‐responsive biomaterials show great promise for modeling disease dynamics ex vivo with spatiotemporal control over the cellular microenvironment. However, harvesting cells from such materials for downstream analysis without perturbing their state remains an outstanding challenge in 3/4‐dimensional (3D/4D) culture and tissue engineering. In this manuscript, a fully enzymatic strategy for hydrogel degradation that affords spatiotemporal control over cell release while maintaining cytocompatibility is introduced. Exploiting engineered variants of the sortase transpeptidase evolved to recognize and selectively cleave distinct peptide sequences largely absent from the mammalian proteome, many limitations implicit to state‐of‐the‐art methods to liberate cells from gels are sidestepped. It is demonstrated that evolved sortase exposure has minimal impact on the global transcriptome of primary mammalian cells and that proteolytic cleavage proceeds with high specificity; incorporation of substrate sequences within hydrogel crosslinkers permits rapid and selective cell recovery with high viability. In composite multimaterial hydrogels, it is shown that sequential degradation of hydrogel layers enables highly specific retrieval of single‐cell suspensions for phenotypic analysis. It is expected that the high bioorthogonality and substrate selectivity of the evolved sortases will lead to their broad adoption as an enzymatic material dissociation cue and that their multiplexed use will enable newfound studies in 4D cell culture.
Precise microscale arrangement of biomolecules and cells is essential for tissue engineering, microarray development, diagnostic sensors, and fundamental research in the biosciences. Biofunctional polymer brushes have attracted broad interest in these applications. However, patterning approaches to creating microstructured biointerfaces based on polymer brushes often involve tedious, expensive, and complicated procedures that are specifically designed for model substrates. We report a substrate-independent, facile, and scalable technique with which to prepare micropatterned biofunctional brushes with the ability to generate binary chemical patterns. Employing chemical vapor deposition (CVD) polymerization, a functionalized polymer coating decorated with 2-bromoisobutyryl groups that act as atom-transfer radical polymerization (ATRP) initiators was prepared and subsequently modified using UV light. The exposure of 2-bromoisobutyryl groups to UV light with wavelengths between 187 and 254 nm resulted in selective debromination, effectively eliminating the initiation of ATRP. In addition, when coatings incorporating both 2-bromoisobutyryl and primary amine groups were irradiated with UV light, the amines retained their functionality after UV treatment and could be conjugated to activated esters, facilitating binary chemical patterns. In contrast, polymer brushes were selectively grown from areas protected from UV treatment, as confirmed by atomic force microscopy, time-of-flight secondary ion mass spectrometry, and imaging ellipsometry. Furthermore, spatial control over biomolecular adhesion was achieved in three ways: (1) patterned nonfouling brushes resulted in nonspecific protein adsorption to areas not covered with polymer brushes; (2) patterned brushes decorated with active binding sides gave rise to specific protein immobilization on areas presenting polymer brushes; (3) and primary amines were co-patterned along with clickable polymer brushes bearing pendant alkyne groups, leading to bifunctional reactivity. Because this novel technique is independent of the original substrate's physicochemical properties, it can be extended to technologically relevant substrates such as polystyrene, polydimethylsiloxane, polyvinyl chloride, and steel. With further work, the photolytic deactivation of CVD-based initiator coatings promises to advance the utility of patterned biofunctional polymer brushes across a spectrum of biomedical applications.
Surface patterning of hydrogel biomaterials offers exciting opportunities to probe and direct cell–matrix interactions. In article number 2001198, Cole A. DeForest and co‐workers highlight recent efforts to govern the biochemical, mechanical, and topographical properties of biocompatible gels for cell culture.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.