The article studies the formation features of the bottomhole zones in productive formations during operation of production wells in the north of the Perm Territory. Their distinctive feature is the high gas saturation of formation oil. The most widely used parameter in Russian and world practice – the skin factor was used as a criterion characterizing the state of the bottomhole zone. Analysis of scientific publications has shown that one of the main problems of applying the skin factor to assess the state of bottomhole zones is the ambiguity of interpretations of its physical meaning and the impossibility of identifying the prevailing factors that form its value. The paper proposes an approach to identifying such factors in the conditions of the fields under consideration, based on multivariate correlation-regression analysis. Choice of this tool is due to the complexity of the processes occurring in the “formation – bottomhole zone – well” system. When describing complex multifactorial processes, the chosen method demonstrates a high degree of reliability. For a large number of wells in the region, significant material was collected and summarized, including the results of determining the skin factor (1102 values) during hydrodynamic investigations, as well as data on the values of various geological and technological indicators, which can probably be statistically related to the value of the skin factor. A series of multidimensional mathematical models has been built; the skin factor was used as a predicted parameter, and data on the values of geological and technological indicators were used as independent indicators. Analysis of the constructed models is a key stage of this study. Set of parameters included in the multidimensional models, sequence of their inclusion and contribution to the total value of the achieved determination coefficient as the main indicator for the performance of the constructed models were studied. It has been established that the main factor influencing the state of the bottomhole zone is oil degassing. Significant differences in the formation features of the skin factor in the terrigenous and carbonate sediments at the fields under consideration have been determined.
В статье представлен анализ существующих общепринятых методов расчета характеристик многофазного потока в стволе скважины. Приведено описание различных методик и их классификация, исследованы ограничения и область применения методов, вынесены рекомендации по использованию. This work contains the analysis of existing common methods for calculation of multiphase flow parameters in wells. Described of different methods and considered their classification. Restrictions and area of their application examined, made recommendations for their use. Введение Многие задачи, связанные с оценкой потенциала и оптимизацией производительности нефтяных и газовых скважин требуют учета многофазного потока в обсадной колонне, насосно-компрессорных трубах и затрубном пространстве. К таким задачам относятся: − расчет забойного давления скважины; − интерпретация гидродинамических исследований скважин; − проведение узлового анализа и расчет рабочей точки системы скважина-пласт; − дизайн системы механизированной добычи; − дизайн и оптимизация конструкции скважины с целью достижения запланированных уровней добычи углеводородов. Для точных расчетов в системах труб нефтяных и газовых скважин необходимо умение прогнозировать поведение газожидкостных потоков в скважинах. Успешное решение перечисленных задач требует применения современных методов расчета характеристик многофазного потока в стволе скважины. В настоящее время существуют общепризнанные методы расчета многофазного потока. Некоторые из них общие, другие же применимы в очень узком диапазоне параметров. Некоторые из них эмпирические, в других, напротив, делаются попытки моделировать явления лежащие в основе тех или иных процессов. Жизненно важно при этом, чтобы человек занимающийся расчетами, связанными с многофазным потоком, знал об ограничениях и области применения того
Ключевые слова: показатели эксплуатации скважин, забойное давление, механизированные скважины, необорудованные глубинными измерительными системами, методика определения забойного давления, статистический анализ, факторы, влияющие на величину забойного давления, корреляция, пошаговый линейный дискриминантный анализ, линейная дискриминантная функция, многомерная математическая модель, разнонаправленность влияния факторов, регрессионный анализ, множественная регрессия, работоспособность модели.Проблема определения забойных давлений в механизированных добывающих скважинах, не оборудованных глубинными измерительными системами, является актуальной для многих нефтяных месторождений Пермского края. На практике, при отсутствии специальных приборов под скважинным насосом, забойное давление определяют путем пересчета динамического уровня. При таком подходе основную сложность представляет расчет плотности газожидкостной смеси, достоверность которого бывает низкой из-за влияния многочисленных осложняющих факторов. В настоящей работе предложен принципиально другой подход к определению забойного давления, рассмотренный на примере одной из добывающих скважин, оснащенных высокоточной глубинной измерительной системой, эксплуатирующей тульско-бобриковскую залежь Юрчукского месторождения. В качестве исходных данных приняты результаты непосредственного измерения забойного давления, а также ряд других показателей ее эксплуатации (дебиты нефти и жидкости, обводненность, динамический уровень, глубина спуска насоса под динамический уровень, давление на устье в затрубном пространстве). Выполненный на первом этапе анализ данных позволил сделать вывод, что забойное давление в период наблюдения изменялось, причем разнонаправленно: сначала постепенно снижалось, затем -увеличивалось. В этой связи исследование влияния показателей эксплуатации на величину забойного давления проведено для трех случаев: для всего периода наблюдений, а также отдельно для периодов его снижения и увеличения. Статистический анализ средних значений и плотностей распределений позволил выделить параметры, оказывающее влияние на величину забойного давления, и установить, что влияние это разнонаправленно. На заключительном этапе построены многомерные статистические модели, учитывающие разнонаправленное влияние показателей эксплуатации на забойное давление. Проверка «работоспособности» разработанных моделей выполнена на примере трех других скважин этого же объекта разработки. Она подтвердила целесообразность использования разработанных моделей для определения величин забойного давления по известным значениям показателей эксплуатации скважин и всего предложенного подхода в целом. Key words:well operation indicators, bottomhole pressure, mechanized wells, unequipped depth measuring systems, method of determining bottomhole pressure, statistical analysis, factors affecting the value of bottomhole pressure; correlation, stepwise linear discriminant analysis, linear discriminant function, multidimensional mathematical model, different directions of influence factors, regression...
-The paper is devoted to the effectiveness increase of monitoring the value of seam pressure when operating oilproducing wells. This problem is relevant for well operation when using subsurface measuring systems. In such cases, seam pressure is determined by recalculation of the dynamic level value, measured at wellhead. The absence of the method of reliable characterization of a multiphase flow leads to substantial errors in the seam pressure, measured in that way. In the present paper, a principally different approach to determination of seam pressure is considered, which is based on the mathematical processing of the accumulated data on parallel wellhead and subsurface measurements. Oil-producing wells, exploiting Famenskaya deposit of Ozyorny field, were chosen as an object of the research. The data on 579 parallel wellhead and subsurface measurements were processed. The use of incremental regression analysis made it possible to develop multidimensional models for Famenskaya deposit, allowing one to determine the seam pressure value in the absence of possibility of its direct measurement. A principle advantage of the developed method is the use of only those parameters as initial data, the determination of which during well operation is not accompanied by difficulties. Comparison of seam pressures, measured and calculated by means of the obtained models, demonstrates high reliability of the developed method.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.