Data from the literature suggest that the rebound of a drop from a surface can be achieved when the wettability is low, i.e., when contact angles, measured at the triple line (solid-liquid-air), are high. However, no clear criterion exists to predict when a drop will rebound from a surface and which is the key wetting parameter to govern drop rebound (e.g., the "equilibrium" contact angle, θeq, the advancing and the receding contact angles, θA and θR, respectively, the contact angle hysteresis, Δθ, or any combination of these parameters). To clarify the conditions for drop rebound, we conducted experimental tests on different dry solid surfaces with variable wettability, from hydrophobic to superhydrophobic surfaces, with advancing contact angles 108° < θA < 169° and receding contact angles 89° < θR < 161°. It was found that the receding contact angle is the key wetting parameter that influences drop rebound, along with surface hydrophobicity: for the investigated impact conditions (drop diameter 2.4 < D0 < 2.6 mm, impact speed 0.8 < V < 4.1 m/s, Weber number 25 < We < 585), rebound was observed only on surfaces with receding contact angles higher than 100°. Also, the drop rebound time decreased by increasing the receding contact angle. It was also shown that in general care must be taken when using statically defined wetting parameters (such as advancing and receding contact angles) to predict the dynamic behavior of a liquid on a solid surface because the dynamics of the phenomenon may affect surface wetting close to the impact point (e.g., as a result of the transition from the Cassie-Baxter to Wenzel state in the case of the so-called superhydrophobic surfaces) and thus affect the drop rebound.

Drop rebound is a spectacular event that appears after impact on hydrophobic or superhydrophobic surfaces but can also be induced through the so-called Leidenfrost effect. Here we demonstrate that drop rebound can also originate from another physical phenomenon, the solid substrate sublimation. Through drop impact experiments on a superhydrophobic surface, a hot plate, and solid carbon dioxide (commonly known as dry ice), we compare drop rebound based on three different physical mechanisms, which apparently share nothing in common (superhydrophobicity, evaporation, and sublimation), but lead to the same rebound phenomenon in an extremely wide temperature range, from 300 °C down to even below -79 °C. The formation and unprecedented visualization of an air vortex ring around an impacting drop are also reported.

Oxidized multiwalled carbon nanotubes were produced by strong acid treatment with the aid of sonication. Short-length carbon nanotubes obtained by filtration of the oxidized carbon nanotubes were analyzed by means of X-ray photoelectron spectroscopy, Raman and photoluminescence spectroscopies, and scanning electron microscopy. Direct evidence of the modifications of the electronic properties of the carbon nanotubes was obtained by the valence band analysis. The oxidation induced by the acid treatment led to deep changes of the carbon nanotubes density of states. Analysis of the photoluminescence spectra showed that the short carbon nanotubes are luminescent in the visible range. Interestingly, the spectral intensities and lineshapes are strongly dependent on the pH of the CNT solution. This effect is explained by a modification of the local environment of the defects induced by the protonation/deprotonation of the carboxylic groups formed by the oxidation process.

Superhydrophobic surfaces (SHS) show remarkable water repellency properties, and their use may have a tremendousimpact for a plethora of applications, where liquid water accumulation needs to be controlled or minimised. However, the durability of SHS in operational conditions is a severe issue that currently represents a bottleneck for the technology transfer from laboratory to industrial applications. In the present work, we try to fill in the gap caused by the absence of a standard for evaluation for SHS durability, by developing a protocol for testing surface durability.The proposed protocol includes nine tests as follows: water immersion, acidic environment, alkaline environment, ionic solution, mechanical erosion, ultraviolet exposure, resistance to heating, alcohol immersion and hydrocarbon immersion. The protocol can serve to give an indication of surface robustness in a variety of potentially harmful environments, by providing a global figure of merit and ranking for different SHS and thereby allowing for identifying those surfaces fulfilling requirements for a specific application. To illustrate the protocol, we tested a SHS developed in-house by grafting of lauric acid molecules on an aluminum substrate. This article contains supporting information that is available online.

No abstract

No abstract

No abstract

No abstract