The analysis of operating conditions of induction traction motors as part of traction electric drives of electric locomotives reported here has revealed that they are powered by autonomous voltage inverters with asymmetric non-sinusoidal voltage. It was established that the induction motor operation may be accompanied by defects caused by the asymmetrical modes of the motor stator. A model of the induction motor has been proposed that takes into consideration changes in the values of mutual inductance of phases and complete inductance of the magnetization circuit due to changes in the geometric dimensions of the winding caused by a certain defect. An algorithm that considers the saturation of the magnetic circuit of the electric motor has been proposed. This approach to modeling an induction motor is important because if one of the stator's windings is damaged, its geometry changes. This leads to a change in the mutual inductance of phases and the complete inductance of the magnetization circuit. Existing approaches to modeling an induction motor do not make it possible to fully take into consideration these changes. The result of modeling is the determined starting characteristics for an intact and damaged engine. The comparison of modeling results for an intact engine with specifications has shown that the error in determining the controlled parameters did not exceed 5 %. The modeling results for the damaged engine demonstrated that the nature of change in the controlled parameters did not contradict the results reported by other authors. The discrepancy in determining the degree of change in the controlled parameters did not exceed 10 %. That indicates a high reliability of the modeling results. The proposed model of an induction electric motor could be used to investigate electromagnetic processes occurring in an electric motor during its operation as part of the traction drive of electric locomotives
Goal. The goal of the research is to develop an algorithm for selecting the main dimensions of a traction permanent magnet-assisted synchronous reluctance motor. Methodology. A method for determining the main dimensions of the motor, which combines the analytical selection of stator parameters and numerical field calculations for the selection of rotor parameters. The need to check the mechanical strength of a rotor with permanent NdFeB magnets in flux barriers is shown. Results. The article proposes an algorithm for selecting the main dimensions of a traction permanent magnet-assisted synchronous reluctance motor, which combines analytical expressions for selecting stator parameters and numerical field calculations for selecting rotor parameters. It is determined that analytical methods for calculating the magnetic circuit need to be developed in order to reduce the time to select the main dimensions of the motor. Originality. For the first time the sizes of active parts of the permanent magnet-assisted synchronous reluctance motor with power of 180 kW for the drive of wheels of the trolleybus are defined. Practical significance. As a result of research the sizes of active parts, stator winding data and a design of a rotor of the electric motor are defined. The obtained results can be applied when creating an electric motor for a trolleybus.
Shunting is an integral part of the partial process. In 1520 mm gauge countries, shunting operations are performed by outdated locomotives, which are being replaced by modern models; the technical parameters best match the conditions of the shunting work performed. The article analyzes recommendations for the selection of parameters of shunting locomotives and the actual indicators of their work. On the basis of this analysis, a requirement was made on the necessity of compulsory consideration of the operating conditions of the locomotive when determining its technical characteristics. As the main technical parameters of shunting locomotives, the tractive power and starting tractive force are taken and their influence on the duration of an elementary shunting movement of the "acceleration-deceleration" type is investigated. This approach advises the regulatory documentation for the organization of shunting work. Tha developed mathematical model allows to carry out research on the influence of tractive power and starting tractive force on the time of acceleration and deceleration. Calculations of the time of the train's acceleration are carried out with varying their mass and the slope of the track at different values of the tractive power starting tractive force. The calculations were carried out for the mass of compositions 1000...5000 Mg for the profile slopes equal to 0 and 1.5 ‰. The speed of the finish of acceleration was taken equal to 15 and 25 km/h. The thrust starting tractive force varied in the range of 150...300 kN, the tractive power - 200 ... 1100 kW. According to the results of calculations, it was found that the reduction in the duration of the elementary shunting movement is more significantly affected by the power of the locomotive than by the starting traction force. The “saturation” effect was noted, in which a significant increase in power or traction force during starting does not cause a significant reduction in the acceleration time. In this regard, for shunting locomotives with AC traction drive, it is recommended to take a pulling force of an equal continuous traction force.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.