Hybrid organic-inorganic halide perovskites are under intense investigations because of their astounding physical properties and promises for optoelectronics. Lead bromide and chloride perovskites exhibit intrinsic white-light emission believed to arise from self-trapped excitons (STEs). Here, we report a series of new structurally diverse hybrid lead bromide perovskites that have broad-band emission at room temperature. They feature Pb/Br structures which vary from 1D face-sharing structures to 3D corner- and edge-sharing structures. Through single-crystal X-ray diffraction and low-frequency Raman spectroscopy, we have identified the local distortion level of the octahedral environments of Pb within the structures. The band gaps of these compounds range from 2.92 to 3.50 eV, following the trend of "corner-sharing < edge-sharing < face-sharing". Density functional theory calculations suggest that the electronic structure is highly dependent on the connectivity mode of the PbBr octahedra, where the edge- and corner-sharing 1D structure of (2,6-dmpz)PbBr exhibits more disperse bands and smaller band gap (2.49 eV) than the face-sharing 1D structure of (hep)PbBr (3.10 eV). Using photoemission spectroscopy, we measured the energies of the valence band of these compounds and found them to remain almost constant, while the energy of conduction bands varies. Temperature-dependent PL measurements reveal that the 2D and 3D compounds have narrower PL emission at low temperature (∼5 K), whereas the 1D compounds have both free exciton emission and STE emission. The 1D compound (2,6-dmpz)PbBr has the highest photoluminescence quantum yield of 12%, owing to its unique structure that allows efficient charge carrier relaxation and light emission.

Two-dimensional (2D) halide perovskites have extraordinary optoelectronic properties and structural tunability. Among them, the Dion-Jacobson phases with the inorganic layers stacking exactly on top of each other are less explored. Herein, we present the new series of 2D Dion-Jacobson halide perovskites, which adopt the general formula of A ′ A n-1 Pb n I 3n+1 (A ′ = 4-(aminomethyl)pyridinium (4AMPY), A = methylammonium (MA), n = 1−4). By modifying the position of the-CH 2 NH 3 + group from 4AMPY to 3AMPY (3AMPY = 3-(aminomethyl)pyridinium), the stacking of the inorganic layers changes from exactly eclipsed to slightly offset. The perovskite octahedra tilts are also different between the two series, with the 3AMPY series exhibiting smaller bandgaps than the 4AMPY series. Compared to the aliphatic cation of the same size (AMP = (aminomethyl)piperidinium), the aromatic spacers increase the rigidity of the cation, reduce the interlayer spacing and decrease the dielectric mismatch between inorganic layer and the organic spacer, showing the indirect but powerful influence of the organic cations on the structure and consequently on the optical properties of the perovskite materials. All A ′ A n-1 Pb n I 3n+1 compounds exhibit strong photoluminescence (PL) at room temperature. Preliminary solar cell devices based on the n = 4 perovskites as absorbers of both series exhibit promising performances, with a champion power conversion efficiency (PCE) of 9.20 % for (3AMPY)(MA) 3 Pb 4 I 13 based devices, which is higher than the (4AMPY)(MA) 3 Pb 4 I 13 and the corresponding aliphatic analogue (3AMP)(MA) 3 Pb 4 I 13 based ones.

The unique hybrid nature of 2D Ruddlesden–Popper (R–P) perovskites has bestowed upon them not only tunability of their electronic properties but also high-performance electronic devices with improved environmental stability as compared to their 3D analogs. However, there is limited information about their inherent heat, light, and air stability and how different parameters such as the inorganic layer number and length of organic spacer molecule affect stability. To gain deeper understanding on the matter we have expanded the family of 2D R–P perovskites, by utilizing pentylamine (PA)2(MA) n−1Pb n I3n+1 (n = 1–5, PA = CH3(CH2)4NH3 +, C5) and hexylamine (HA)2(MA) n−1Pb n I3n+1 (n = 1–4, HA = CH3(CH2)5NH3 +, C6) as the organic spacer molecules between the inorganic slabs, creating two new series of layered materials, for up to n = 5 and 4 layers, respectively. The resulting compounds were extensively characterized through a combination of physical and spectroscopic methods, including single crystal X-ray analysis. High resolution powder X-ray diffraction studies using synchrotron radiation shed light for the first time to the phase transitions of the higher layer 2D R–P perovskites. The increase in the length of the organic spacer molecules did not affect their optical properties; however, it has a pronounced effect on the air, heat, and light stability of the fabricated thin films. An extensive study of heat, light, and air stability with and without encapsulation revealed that specific compounds can be air stable (relative humidity (RH) = 20–80% ± 5%) for more than 450 days, while heat and light stability in air can be exponentially increased by encapsulating the corresponding films. Evaluation of the out-of-plane mechanical properties of the corresponding materials showed that their soft and flexible nature can be compared to current commercially available polymer substrates (e.g., PMMA), rendering them suitable for fabricating flexible and wearable electronic devices.

No abstract

Semiconductor heterostructured seeded nanorods exhibit intense polarized emission, and the degree of polarization is determined by their morphology and dimensions. Combined optical and atomic force microscopy were utilized to directly correlate the emission polarization and the orientation of single seeded nanorods. For both the CdSe/CdS sphere-in-rod (S@R) and rod-in-rod (R@R), the emission was found to be polarized along the nanorod's main axis. Statistical analysis for hundreds of single nanorods shows higher degree of polarization, p, for R@R (p = 0.83), in comparison to S@R (p = 0.75). These results are in good agreement with the values inferred by ensemble photoselection anisotropy measurements in solution, establishing its validity for nanorod samples. On this basis, photoselection photoluminescence excitation anisotropy measurements were carried out providing unique information concerning the symmetry of higher excitonic transitions and allowing for a better distinction between the dielectric and the quantum-mechanical contributions to polarization in nanorods.