Surfactant flooding is an important technique used in enhanced oil recovery to reduce the amount of oil in pore space of matrix rock. Surfactants are injected to mobilize residual oil by lowering the interfacial tension between oil and water and/or by the wettability alteration from oil-wet to water-wet. A large number of cationic, anionic, non-ionic, and amphoteric surfactants have been investigated on a laboratory scale under different conditions of temperature and salinity. Selection of the appropriate surfactant is a challenging task, and surfactants have to be evaluated by a series of screening techniques. Different types of surfactants along with their limitations are reviewed with particular emphasis on the phase behavior, adsorption, interfacial tension, and structure−property relationship. Factors affecting the phase behavior, interfacial tension, and wettability alteration are also discussed. Field applications of surfactants for chemical enhanced oil recovery in carbonate and sandstone reservoirs are also reviewed. Finally, some recent trends and future challenges in surfactant enhanced oil recovery are outlined. Field studies show that most of the surfactant flooding has been conducted in low-temperature and low-salinity sandstone reservoirs. However, high-temperature and high-salinity carbonate reservoirs are still challenging for implementation of surfactant flooding.

Polymer flooding is one of the most promising techniques for the recovery of remaining oil from light oil reservoirs. Water soluble polymers are used to enhance the viscosity of displacing fluid and to improve the sweep efficiency. In this paper, water soluble polymers used for chemical enhanced oil recovery are reviewed. Conventional and novel modified polymers are discussed along with their limitations. The review covers thermal stability, rheology, and adsorption behavior of various polymer systems in sandstone and carbonate reservoirs. Field and laboratory core flooding data of several polymers are covered. The review describes the polymer systems that are successfully applied in low-temperature and low-salinity reservoirs. Comprehensive review of current research activities aiming at extending polymer flooding to high-temperature and high-salinity reservoirs is performed. The review has identified current and future challenges of polymer flooding.

Unwanted water production is a serious issue in oil-and gas-producing wells. It causes corrosion, scale, and loss of productivity. One method of treating this problem is to chemically reduce unwanted water. This paper discusses the use of polymer systems for this purpose and presents a thorough review of available literature over the last decade. In this paper, field-application data for various polymer systems are summarized over the range of 40 to 150 C (104 to 302 F). These applications cover a wide range of permeabilities from 20 to 2,720 md in sandstone and carbonate reservoirs around the globe. Moreover, the review revealed that the last decade of developments can be categorized into two major types. The first type is polymer gels for total water shutoff in the near-wellbore region, in which a polymer is crosslinked with either an organic or an inorganic crosslinker. The second type is concerned with deep treatment of water-injection wells diverting fluids away from high-permeability zones (thief zones). These thief zones take most of the injected water, which results in a large amount of unrecovered oil. For the total-blocking gels, various systems were identified, such as polyurethane resins, chromium (Cr 3þ ) crosslinking terpolymers, Cr 3þ crosslinking foamed partially hydrolyzed polyacrylamide (PHPA), and nanoparticle polyelectrolyte complexes (PECs) sequestering Cr 3þ for elongation of its gelation time with PHPA. In addition, polyethylenimine (PEI) was identified to crosslink various polyacrylamide-(PAM-) based polymers. The Petróleos de Venezuela S.A. (PDVSA) Research and Development Center developed a PAM-based thermally stable polymer and an organic crosslinker. The system is applicable for a wide temperature range from 50 to 160 C (130 to 320 F).For the deep modification of water-injection profiles in waterinjection wells, two systems were identified: microspheres prepared from PAM monomers crosslinked with N,N 0 -methylenebisacrylamide and microspheres produced by crosslinking 2-acrylamido-2-methylpropane sulfonic acid (AMPS) with diacrylamides and methacrylamides of diamines (thermally activated microparticles known as Bright Water). This paper highlights all major developments in these areas. Important Factors for Successful CITsThe identification of the water source is a key factor for successful CITs. The characterization of water production can be performed

No abstract

No abstract

No abstract

Solar energy is an abundant and accessible source of renewable energy available on earth, and many types of photovoltaic (PV) devices like organic, inorganic, and hybrid cells have been developed to harness the energy. PV cells directly convert solar radiation into electricity without affecting the environment. Although silicon based solar cells (inorganic cells) are widely used because of their high efficiency, they are rigid and manufacturing costs are high. Researchers have focused on organic solar cells to overcome these disadvantages. DSSCs comprise a sensitized semiconductor (photoelectrode) and a catalytic electrode (counter electrode) with an electrolyte sandwiched between them and their efficiency depends on many factors. The maximum electrical conversion efficiency of DSSCs attained so far is 11.1%, which is still low for commercial applications. This review examines the working principle, factors affecting the efficiency, and key challenges facing DSSCs.

No abstract