Greenhouses are important for stable food production, but require large amounts of energy to maintain their microclimate in regions with harsh climates. This study assessed the internal thermal insulation performance of thermal curtains in double-layered plastic greenhouses in Korea in winter using cover surface temperature changes and heat transfer coefficients (U values). The thermal curtain performance increased as the temperatures of the inner cover surface increased and the outer cover surface decreased. The outer cover surface temperature with thermal curtains was almost uniformly 1.9 °C lower than that without thermal curtains, whereas the inner cover surface temperature was higher, demonstrating the warming effect of thermal curtain use. Under a constant indoor and outdoor air temperature difference, the daily average heating energy consumption was directly proportional to the U value. The U values were 2.76 W m−2 °C−1 with thermal curtains and 3.85 W m−2 °C−1 without thermal curtains. In double-layered plastic greenhouses that were covered with 0.1-mm-thick polyethylene, incorporating thermal curtains at night resulted in energy savings of about 28.7%, which was related to the decrease in U values. Installing and using thermal curtains at night in winter is a highly economical method for heating savings. These results can be used to promote energy savings in greenhouses in harsh climates.

This study compared and analyzed changes in the microclimate and thermal environment inside single-span greenhouses covered with a single layer of plastic film, polycarbonate (PC), and glass. The results of the experiment show that the PC-covered greenhouse was the most favorable for managing the nighttime heating effect during the cold season. However, the glass-covered greenhouse was found to be the most favorable for managing the cooling effect during the hot season. Although the plastic-covered greenhouse was inexpensive and easy to install, the air temperature inside varied significantly, and it was difficult to control its indoor environment. The thermal load leveling values showed that the PC-covered greenhouse had the lowest variation, confirming its superiority in terms of environmental control and energy savings. In terms of the overall heat transfer, heat was generally transferred from the interior to the exterior of the greenhouses. In the plastic-covered greenhouse, however, heat was transferred in the opposite direction at night due to the influence of radiant cooling. The occurrence of the minimum and maximum heat transfer values had a tendency similar to that of the occurrence of the minimum and maximum air temperatures inside the greenhouses.

No abstract

This study comprehensively analyzed the heat loss and total heat transfer coefficient (U-value) of a single-span experimental plastic greenhouse covered with a double layer of 0.1 mm thick polyethylene. The air temperature and heat flux (W m−2) of the greenhouse components were measured from 18:00 to 06:00, and the energy balance equations under steady-state conditions were determined. The heat flux and U-value of the roof, sides, front and rear, and floor of the greenhouse were determined and compared. The results showed that these values for the roof play an important role in determining the heat load in the greenhouse, and that the average heat transfer through the floor is very small. The average U-value of the greenhouse cover is a comprehensive value which takes the U-values of the roof, sides, and front and rear into account through the use of an area–weighted average method. Finally, an average U-value of 3.69 W m−2 °C −1 was obtained through the analysis of the variations in the U-value, as it is related to the difference in air temperature between the interior and exterior of the greenhouse, as well as to the outdoor wind speed. The relationships between the average U-value and those of the roof, sides, and front and rear of the experimental greenhouse were modeled, and were shown to have a highly linear relationship.

This study was carried out to investigate quantitative characteristics of the cooling effect in a single-span arch greenhouse with roll-up side vents depending on operation of circulation and exhaust fans during ventilation, in order to suggest a practical strategy regarding installation or operation of forced ventilation systems. The examination was conducted under 3 different ventilation conditions (side vents only, side vents + circulation fans, and side vents + circulation fans + exhaust fans). In each condition, variations of internal and external air temperatures and exogenous environmental factors were recorded during ventilation, and the cooling effects were investigated by comparing the normalized temperature difference (NTD) of each ventilation condition. In the morning time (11:00-12:00), a temporary peak in the temperature difference was observed at the beginning of ventilation regardless of ventilation methods. The time taken to the maximum NTD was decreased from 340 s to 110s, and the NTD was dropped from 1.158 to 1.037 as the more forced ventilation systems were operated. The more operations caused the passing time over specific NTD values reduced by 60% as the time was reduced from 1,030 s to 550 s at NTD = 0.8, 1,610 s to 915 s at NTD = 0.6, and 2,315 s to 1,360 s at NTD = 0.4. The temporary peak in NTD was not observed in the afternoon time (14:00-15:00) but it was dropped as quickly as the ventilation started. Also the more operations resulted in the passing time over specific NTD values reduced by 70% as the time was reduced from 560 s to 345 s at NTD = 0.8, from 825 s to 540 s at NTD = 0.6, and from 1,145 s to 810 s at NTD = 0.4. Conclusively, the intervention of the forced ventilation system is recommended in the morning time or in high thermal conditions to achieve more effective and economical ventilation.

The purpose of this study is to suggest structural model and analyze design factors for the development of small greenhouse standardization model. The average dimensions of small greenhouse desired by urban farmers were 3.3m in width, 1.9m in eaves height, 2.7m in ridge height, 5.7m in length. The cladding materials for small greenhouse were preferred to glass, PC board and plastic film, framework to aluminum alloy and steel, and heating method in electrical energy. In addition, it was analyzed that small greenhouses need to develop structural model by dividing them into entry-level type and high-level type. The roof type that was used for entry-level type was arch shape, framework was steel pipe, cladding material was plastic film. On the other hand, high-level type was used in even span or dutch light type, framework with square hollow steel, cladding materials with glass or PC board. In consideration of these findings and practicality, this study developed four types of small greenhouses. The width, eaves height, ridges height, and length of the small greenhouses of even span type, which were covered with 5mm thick glass and 6mm thick PC board were 3m, 2.2m, 2.9m, and 6m, respectively. The small greenhouse of dutch light type covered with 5mm thick glass was designed with 3.8m in with, 2.2m in eaves height, 2.9m in ridges height, and 6m in length. The width, eaves height, ridges height, and length of the arch shape small greenhouse covered with a 0.15mm PO film were 3m, 1.5m, 2.8m, and 6m, respectively.

No abstract

No abstract