A soft-bodied robot made of smart soft composite with inchworm-inspired locomotion capable of both two-way linear and turning movement has been proposed, developed, and tested. The robot was divided into three functional parts based on the different functions of the inchworm: the body, the back foot, and the front foot. Shape memory alloy wires were embedded longitudinally in a soft polymer to imitate the longitudinal muscle fibers that control the abdominal contractions of the inchworm during locomotion. Each foot of the robot has three segments with different friction coefficients to implement the anchor and sliding movement. Then, utilizing actuation patterns between the body and feet based on the looping gait, the robot achieves a biomimetic inchworm gait. Experiments were conducted to evaluate the robot's locomotive performance for both linear locomotion and turning movement. Results show that the proposed robot's stride length was nearly one third of its body length, with a maximum linear speed of 3.6 mm s(-1), a linear locomotion efficiency of 96.4%, a maximum turning capability of 4.3 degrees per stride, and a turning locomotion efficiency of 39.7%.

No abstract

The one-dimensional deformation of shape memory alloy (SMA) wires and springs can be implemented into different types of functional structures with three-dimensional deformations. These structures can be classified based on the type of structure and how the SMA element has been implemented into the following categories: rigid mechanical joints, semi-rigid flexural hinges, SMA elements externally attached to a soft structure, and embedded into the soft structure. These structures have a wide range of properties and implementation requirements, and they have been used to produce a variety of robots with rigid and soft motions. The different research efforts to develop actuators and robots related to each type of structure are presented along with their respective strengths and weaknesses. A model is then developed to discuss the performance and applicability of SMA wires versus SMA springs for actuators with a polymeric matrix to see the effect of each type of SMA on the selection of design parameters. A comparison of the different types of structures and the applicability of different types of SMA elements for different types of structures is then presented.

No abstract

Shape memory alloy (SMA) wire-based soft actuators have had their performance limited by the small stroke of the SMA wire embedded within the polymeric matrix. This intrinsically links the bending angle and bending force in a way that made SMA-based soft grippers have relatively poor performance versus other types of soft actuators. In this work, the use of free-sliding SMA wires as tendons for soft actuation is presented that enables large increases in the bending angle and bending force of the actuator by decoupling the length of the matrix and the length of the SMA wires while also allowing for the compact packaging of the driving SMA wires. Bending angles of 400° and tip forces of 0.89 N were achieved by the actuators in this work using a tendon length up to 350 mm. The tendons were integrated as a compact module using bearings that enables the actuator to easily be implemented in various soft gripper configurations. Three fingers were used either in an antagonistic configuration or in a triangular configuration and the gripper was shown to be capable of gripping a wide range of objects weighing up to 1.5 kg and was easily installed on a robotic arm. The maximum pulling force of the gripper was measured to be 30 N.

This paper presents a biomimetic turtle flipper actuator consisting of a shape memory alloy composite structure for implementation in a turtle-inspired autonomous underwater vehicle. Based on the analysis of the Chelonia mydas, the flipper actuator was divided into three segments containing a scaffold structure fabricated using a 3D printer. According to the filament stacking sequence of the scaffold structure in the actuator, different actuating motions can be realized and three different types of scaffold structures were proposed to replicate the motion of the different segments of the flipper of the Chelonia mydas. This flipper actuator can mimic the continuous deformation of the forelimb of Chelonia mydas which could not be realized in previous motor based robot. This actuator can also produce two distinct motions that correspond to the two different swimming gaits of the Chelonia mydas, which are the routine and vigorous swimming gaits, by changing the applied current sequence of the SMA wires embedded in the flipper actuator. The generated thrust and the swimming efficiency in each swimming gait of the flipper actuator were measured and the results show that the vigorous gait has a higher thrust but a relatively lower swimming efficiency than the routine gait. The flipper actuator was implemented in a biomimetic turtle robot, and its average swimming speed in the routine and vigorous gaits were measured with the vigorous gait being capable of reaching a maximum speed of 11.5 mm s(-1).

Shape Memory Alloy (SMA) materials are widely used as an actuating source for bending actuators due to their high power density. However, due to the slow actuation speed of SMAs, there are limitations in their range of possible applications. This paper proposes a smart soft composite (SSC) actuator capable of fast bending actuation with large deformations. To increase the actuation speed of SMA actuator, multiple thin SMA wires are used to increase the heat dissipation for faster cooling. The actuation characteristics of the actuator at different frequencies are measured with different actuator lengths and results show that resonance can be used to realize large deformations up to 35 Hz. The actuation characteristics of the actuator can be modified by changing the design of the layered reinforcement structure embedded in the actuator, thus the natural frequency and length of an actuator can be optimized for a specific actuation speed. A model is used to compare with the experimental results of actuators with different layered reinforcement structure designs. Also, a bend-twist coupled motion using an anisotropic layered reinforcement structure at a speed of 10 Hz is also realized. By increasing their range of actuation characteristics, the proposed actuator extends the range of application of SMA bending actuators.

The beam steering mechanism has been a key element for various applications ranging from sensing and imaging to solar tracking systems. However, conventional beam steering systems are bulky and complex and present significant challenges for scaling up. This work introduces the use of soft deployable reflectors combining a soft deployable structure with simple kirigami/origami reflective films. This structure can be used as a macroscale beam steering mechanism that is both simple and compact. This work first develops a soft deployable structure that is easily scalable by patterning of soft linear actuators. This soft deployable structure is capable of increasing its height several folds by expanding in a continuous and controllable manner, which can be used as a frame to deform the linearly stretchable kirigami/origami structures integrated into the structure. Experiments on the reflective capability of the reflectors are conducted and show a good fit to the modeling results. The proposed principles for deployment and for beam steering can be used to realize novel active beam steering devices, highlighting the use of soft robotic principles to produce scalable morphing structures.