Triboelectrification-induced electroluminescence converts dynamic motion into light emission. Tribocharges resulting from the relative mechanical interactions between two dissimilar materials can abruptly and significantly alter the surrounding electric potential, exciting the electroluminescence of phosphor along the motion trajectory. The position, trajectory, and contour profile of a moving object can be visualized in high resolution, demonstrating applications in sensing.

Skin sensors are of paramount importance for flexible wearable electronics, which are active in medical diagnosis and healthcare monitoring. Ultrahigh sensitivity, large measuring range, and high skin conformability are highly desirable for skin sensors. Here, an ultrathin flexible piezoresistive sensor with high sensitivity and wide detection range is reported based on hierarchical nanonetwork structured pressuresensitive material and nanonetwork electrodes. The hierarchical nanonetwork material is composed of silver nanowires (Ag NWs), graphene (GR), and polyamide nanofibers (PANFs). Among them, Ag NWs are evenly interspersed in a PANFs network, forming conductive pathways. Also, GR acts as bridges of crossed Ag NWs. The hierarchical nanonetwork structure and GR bridges of the pressure-sensitive material enable the ultrahigh sensitivity for the pressure sensor. More specifically, the sensitivity of 134 kPa −1 (0−1.5 kPa) and the low detection of 3.7 Pa are achieved for the pressure sensor. Besides, the nanofibers act as a backbone, which provides effective protection for Ag NWs and GR as pressure is applied. Hence, the pressure sensor possesses an excellent durability (>8000 cycles) and wide detection range (>75 kPa). Additionally, ultrathin property (7 μm) and nanonetwork structure provide high skin conformability for the pressure sensor. These superior performances lay a foundation for the application of pressure sensors in physiological signal monitoring and pressure spatial distribution detection.

Excellent triboelectric and mechanical properties are achieved on the same material for the first time by developing an effective, general, straightforward, and area‐scalable approach to surface modification of a polyethylene terephthalate (PET) film via inductive‐coupled plasma etching. The modification enables gigantic enhancement of triboelectric charge density on the PET surface. Based on the modified PET as a contact material, a triboelectric nanogenerator (TENG) exhibits significantly promoted electric output compared to the one without the modification. The obtained electric output is even superior to a TENG made of conventional polytetrafluoroethylene that is known for its strongest ability of being charged by triboelectrification among all engineering plastics. Detailed characterizations reveal that the enhancement of triboelectric charge density on the PET is attributed to both chemical modification of fluorination and physical modification of roughened morphology in nanoscale. Therefore, this work proposes a new route to obtaining high‐performance TENGs by manipulating and modifying surface properties of materials.

We report a MAPbI3-based self-powered photodetector (SPPD). It has a dual sensing mechanism that relies on the joint properties of a photoelectric effect and a triboelectric effect of the perovskite material. Both the photoconductivity and the surface triboelectric density of the MAPbI3-based composite thin film are significantly altered upon solar illumination, which results in considerable reduction of the output voltage. The SPPD exhibits excellent responsivity (7.5 V W(-1)), rapid response time (<80 ms), great repeatability, and broad detection range that extends from UV to visible regions. This work presents a route to designing high-performance self-powered photodetectors from the aspect of materials.

A stretchable porous nanocomposite (PNC) is reported based on a hybrid of a multiwalled carbon nanotubes network and a poly(dimethylsiloxane) matrix for harvesting energy from mechanical interactions. The deformation-enabled energy-generating process makes the PNC applicable to various mechanical interactions, including pressing, stretching, bending, and twisting. It can be potentially used as an energy solution for wearable electronics.

We report a flexible and area-scalable energy-harvesting technique for converting kinetic wave energy. Triboelectrification as a result of direct interaction between a dynamic wave and a large-area nanostructured solid surface produces an induced current among an array of electrodes. An integration method ensures that the induced current between any pair of electrodes can be constructively added up, which enables significant enhancement in output power and realizes area-scalable integration of electrode arrays. Internal and external factors that affect the electric output are comprehensively discussed. The produced electricity not only drives small electronics but also achieves effective impressed current cathodic protection. This type of thin-film-based device is a potentially practical solution of on-site sustained power supply at either coastal or off-shore sites wherever a dynamic wave is available. Potential applications include corrosion protection, pollution degradation, water desalination, and wireless sensing for marine surveillance.

Flexible pressure sensors have attracted intense attention because of their widespread applications in electronic skin, human−machine interfaces, and healthcare monitoring. Conductive porous structures are always utilized as active layers to improve the sensor sensitivities. However, flexible pressure sensors derived from traditional foaming techniques have limited structure designability. Besides, random pore distribution causes difference in structure and signal repeatability between different samples even in one batch, therefore limiting the batch production capabilities. Herein, we introduce a structure designable lattice structure pressure sensor (LPS) produced by bottom-up digital light processing (DLP) 3D printing technique, which is capable of efficiently producing 55 high fidelity lattice structure models in 30 min. The LPS shows high sensitivity (1.02 kPa −1 ) with superior linearity over a wide pressure range (0.7 Pa to 160 kPa). By adjusting the design parameters such as lattice type and layer thickness, the electrical sensitivities and mechanical properties of LPS can be accurately controlled. In addition, the LPS endures up to 60000 compression cycles (at 10 kPa) without any obvious electrical signal degradation. This benefits from the firm carbon nanotubes (CNTs) coating derived from high-energy ultrasonic probe and the subsequent thermal curing process of UV-heat dual-curing photocurable resin. For practical applications, the LPS is used for real time pulse monitoring, voice recognition and Morse code communication. Furthermore, the LPS is also integrated to make a flexible 4 × 4 sensor arrays for detecting spatial pressure distribution and a flexible insole for foot pressure monitoring.

Extremely soft and thin electrodes with high skin conformability have potential applications in wearable devices for personal healthcare. Here, a submicrometer thick, highly robust, and conformable nanonetwork epidermal electrode (NEE) is reported. Electrospinning of polyamide nanofibers and electrospraying of silver nanowires are simultaneously performed to form a homogeneously convoluted network in a nonwoven way. For a 125 nm thick NEE, a low sheet resistance of ≈4 Ω sq−1 with an optical transmittance of ≈82% is achieved. Due to the nanofiber‐based scaffold that undertakes most of the stress during deformation, the electric resistance of the NEE shows very little variation; less than 1.2% after 50 000 bending cycles. The NEE can form a fully conformal contact to human skin without additional adhesives, and the NEE shows a contact impedance that is over 50% lower than what is found in commercial gel electrodes. Due to conformal contact even under deformation, the NEE proves to be a stable, robust, and comfortable approach for measuring electrocardiogram signals, especially when a subject is in motion. These features make the NEE promising for use in the ambulatory measurement of physiological signals for healthcare applications.