No abstract

We propose and demonstrate a simple water level monitoring system based on the wavelength division multiplexing (WDM) for the spent fuel pool (SFP) at a nuclear power plant. The basic principle is based on the measurement of the optical power spectra by the Fresnel reflection according to the change of the refractive index at the end facet of the optical fiber tip (OFT). An arrayed waveguide grating (AWG) is employed to achieve multi-channel sensing capability with a C-band broadband light source (BLS) based on amplified spontaneous emission (ASE). The feasibility of the proposed scheme is investigated with a simulation and experimentation. We also investigate the limiting factor for remote transmission. The system performance is degraded by the Rayleigh backscattering of the BLS light, but it can be operated over long distances within 10 km with 5 dB of difference peak power margin.

This paper presents a passive optical fiber sensor network based on the dense wavelength division multiplexing (DWDM) to remotely monitor the water level of the spent fuel pool in nuclear power plants. In states of emergency, such as a tsunami, safety information must be secured for rapid response, in spite of all power losses in the plant. We consider the proposed passive sensor network to be one of the best solutions that is able to provide the remote (more than tens of kilometers) monitoring station with the highly reliable on-site information. The principle of water level measurement is based on the change of Fresnel reflection power coefficient at sensing units, which are installed according to the water levels in a row. The sensing units that play the role of reflector and modulator at the same time are connected to an arrayed waveguide grating (AWG) for DWDM. By measuring the spectrum of the optical signal transferred from the sensing units, the water level can be determined in real-time. However, in the remote sensing, the system performance can be seriously degraded due to the Rayleigh Back-Scattering (RBS) of the seeded amplified spontaneous emission (ASE) light that is induced at the fiber-optic link. As such, we investigate the effect of RBS on the remote (more than tens of kilometers) sensing performance of the proposed network. Following the theoretical analysis, we propose a simple network configuration to overcome the RBS issue by utilizing two different transmission paths: one for downstream of the ASE seed light, and the other for upstream of the optical signals coming from the sensing units. Based on the proposed configuration, the maximum sensing distance can be increased up to 42.5 km without the support of any optical amplifier.

Water management is a critical mission required to protect the water resources that is essential in diverse industrial applications. Amongst a variety of parameters such as level (or depth), temperature, conductivity, turbidity, and pH, the water level is the most fundamental one that needs to be monitored on a real-time basis for securing the water management system. This paper presents an overview of water level monitoring technologies based on optical fiber sensor (OFS) networks. Firstly, we introduce and compare the passive distributed and quasi-distributed (discrete) sensor networks with the recent achievements summarized. The performance (i.e., sensing range and resolution) of the OFS networks can be enhanced through diverse multiplexing techniques based on wavelength, time, coherence, space, etc. Especially, the dense wavelength division multiplexing (DWDM)-based sensor network provides remote sensing (where its reach can be extended to >40 km) with high scalability in terms of the channel number that determines the spatial resolution. We review the operation principle and characteristics of the DWDM-based OFS network with full theoretical and experimental analysis being provided. Furthermore, the key system functions and considerations (such as the link protection from physical damages, self-referencing, management of sensing units, and so on) are discussed that could be a guideline on the design process of the passive OFS network.

This paper presents an analytical interpretation of electromagnetic interference between solid-bottom type open cable trays in a nuclear power plant under the assumption that an electric-line current is undesirably generated from a damaged cable in an open cable tray. Based on the superposition principle and Helmholtz's equation in conjunction with the separation of variables, we employ a mode-matching method to obtain analytical solutions to the postulated electromagnetic interference problem. Before conducting a mode-matching analysis, we investigate the radiating principle of the electric field interfering with a victim cable tray by deriving the array factor in consideration of an imaginary electric-line current. In addition, we characterize the electric fields with a propagating mode at an observation point in the victim cable tray using the derived expression of the electric field. Based on this, we validate the formulation and computation of our mode-matching method and then computationally investigate the strength and distribution of interfering electric fields in terms of the separation distances provided in regulatory guidance on the electrical independence of a nuclear power plant. Finally, we compute the strength and distribution of the interfering electric field at the observation point when the location of an electric-line current is modified. The results of the study provide us with the useful information to alleviate the electromagnetic interference between open cable trays in a nuclear power plant. INDEX TERMSElectromagnetic interference, mode-matching method, open cable tray. FIGURE 2. Allowable E-field strength for RE102 test, modified allowable E-field strengths at distances of 0.025, 0.152, and 0.92 m, and susceptibility threshold level for RS103 test.