Two-dimensional (2D) Ruddlesden-Popper perovskites have shown great potential for application in perovskite solar cells due to their appealing environmental stability. However, 2D perovskites generally show poor photovoltaic performance. Here, a new type of 2D perovskite using 2-thiophenemethylammonium (ThMA) as a spacer cation was developed and high photovoltaic performance as well as enhanced stability in comparison with its 3D counterpart was demonstrated. The use of the 2D perovskite (ThMA)(MA) PbI ( n = 3) in deposited highly oriented thin films from N, N-dimethylformamide using a methylammonium chloride (MACl) assisted film-forming technique dramatically improves the efficiency of 2D perovskite photovoltaic devices from 1.74% to over 15%, which is the highest efficiency for 2D perovskite ( n < 6) solar cells so far. The enhanced performance of the 2D perovskite devices using MACl as additive is ascribed to the growth of a dense web of nanorod-like film with near-single-crystalline quality, in which the crystallographic planes of the 2D MA PbI slabs preferentially aligned perpendicular to the substrate, thus facilitating efficient charge transport. This work provides a new insight into exploration of the formation mechanism of 2D perovskites with increased crystallinity and crystal orientation suitable for high-performance solar cells.

Quasi‐2D Ruddlesden–Popper (RP) perovskite solar cells (PSCs) have drawn significant attention due to their appealing environmental stability compared to their 3D counterparts. However, the relatively low power conversion efficiency (PCE) greatly limits their applications. Here, high photovoltaic performance is demonstrated for quasi‐2D RP PSCs using 2‐thiophenemethylammonium as spacer with nominal n‐value of 5, which is based on the stoichiometry of the precursors. The incorporation of formamidinium (FA) in quasi‐2D RP perovskites reduces the bandgap and improves the light absorption ability, resulting in enlarged photocurrent and an increased PCE of 16.18%, which is higher than that of reported analogous methylammonium (MA)‐based quasi‐2D PSC (≈15%). A record high PCE of 19.06% is further demonstrated by using an organic salt, namely, 4‐(trifluoromethyl)benzylammonium iodide, assisted crystal growth (OACG) technique, which can induce the crystal growth and orientation, tune the surface energy levels, and suppress the charge recombination losses. More importantly, the devices based on OACG‐processed quasi‐2D RP perovskites show remarkable environmental stability and thermal stability, for example, the PCE retaining ≈96% of its initial value after storage at 80 °C for 576 h, while only ≈37% of the original efficiency left for FAPbI3‐based3D PSCs.

Highly efficient and stable 2D/3D hybrid perovskite solar cells using 2‐thiophenemethylammonium (ThMA) as the spacer cation are successfully demonstrated. It is found that the incorporation of ThMA spacer cation into 3D perovskite, which forms a 2D/3D hybrid structure, can effectively induce the crystalline growth and orientation, passivate the trap states, and hinder the ion motion, resulting in improved carrier lifetime and reduced recombination losses. The optimized device exhibits a power conversion efficiency (PCE) of 21.49%, combined with a high VOC of 1.16 V and a notable fill factor (FF) of 81%. More importantly, an encapsulated 2D/3D hybrid perovskite device sustains ≈99% of its initial PCE after 1680 h in the ambient atmosphere, whereas the control 3D perovskite device drops to ≈80% of the original performance. Importantly, the device stability under continuous light soaking (100 mW cm−2) is enhanced significantly for 2D/3D perovskite device in comparison with that of the control device. These results reveal excellent photovoltaic properties and intrinsic stabilities of the 2D/3D hybrid perovskites using ThMA as the spacer cation.

perovskites with natural multi-quantum-well structure have been reported to offer better stability compared to 3D perovskites. However, the understanding of the exciton separation and transport mechanism in 2D perovskites and developing more efficient organic spacers remain considerable challenges, as the 2D perovskites exhibit large exciton binding energy due to quantum confinement. Here, a class of multiple-ring aromatic ammoniums, 1naphthalenemethylammonium (NpMA) and 9-anthracenemethylammonium (AnMA), was developed as spacers for 2D Ruddlesden−Popper (RP) perovskite solar cells (PSCs). In addition to significantly enhanced stability, the device based on (NpMA) 2 (MA) n−1 Pb n I 3n+1 (average n = 4) exhibits a champion efficiency of 17.25% and a high open-circuit voltage of 1.24 V. The outstanding photovoltaic performance could be ascribed to the ultrafast exciton migration (within 7 ps) from 2D phases to 3D-like phases, which were confirmed by charge carrier dynamics results, leading to efficient exciton separation, charge transportation, and collection. This work facilitates understanding the working mechanism of 2D PSCs in-depth and offers an efficient way to further boost their efficiency and stability by developing multiple-ring aromatic spacers.

Formamidinium (FA)‐based 3D perovskite solar cells (PSCs) have been widely studied and they show reduced bandgap, enhanced stability, and improved efficiency compared to MAPbI3‐based devices. Nevertheless, the FA‐based spacers have rarely been studied for 2D Ruddlesden–Popper (RP) perovskites, which have drawn wide attention due to their enormous potential for fabricating efficient and stable photovoltaic devices. Here, for the first time, FA‐based derivative, 2‐thiopheneformamidinium (ThFA), is successfully synthesized and employed as an organic spacer for 2D RP PSCs. A precursor organic salts‐assisted crystal growth technique is further developed to prepare high quality 2D (ThFA)2(MA)n−1PbnI3n+1 (nominal n = 3) perovskite films, which shows preferential vertical growth orientations, high charge carrier mobilities, and reduced trap density. As a result, the 2D RP PSCs with an inverted planar p‐i‐n structure exhibit a dramatically improved power conversion efficiency (PCE) from 7.23% to 16.72% with negligible hysteresis, which is among the highest PCE in 2D RP PSCs with low nominal n‐value of 3. Importantly, the optimized 2D PSCs exhibit a dramatically improved stability with less than 1% degradation after storage in N2 for 3000 h without encapsulation. These findings provide an effective strategy for developing FA‐based organic spacers toward highly efficient and stable 2D PSCs.