The Laoyingqing Pb–Zn deposit is located on the southwestern margin of the Yangtze block and on the east side of the Xiaojiang deep fault in the Sichuan–Yunnan–Guizhou Pb–Zn metallogenic triangle area (SYGT). This deposit was first discovered in the silty and carbonaceous slate of the Middle Proterozoic Kunyang Group that is structurally controlled by thrust faults and anticlines. This study is aimed at investigating whether the Laoyingqing deposit has the same ore-forming age and type as other Pb–Zn deposits related to the Pb–Zn metallogenic system and prospecting prediction of the deep and peripheral areas of the deposits in the SYGT. Based on the sphalerite Rb–Sr age dating and S–Sr–Pb isotopic composition analysis of the Laoyingqing Pb–Zn deposit, the following results were obtained. First, the Rb–Sr isochron age of sphalerite is 209.8 ± 5.2 million years (Ma), consistent with the ages of most Pb–Zn deposits in the SYGT (approximately 200Ma), thereby potentially indicating that these Pb–Zn deposits may have been formed synchronously during the late Indosinian orogeny. Second, the Pb isotopic compositions of sulfides show a linear trend on the average crustal Pb evolution curve in 207Pb/204Pb vs. 206Pb/204Pb plot. In addition, Pb isotopic ratios were consistent with the age-corrected Pb isotopic ratios of basement rocks, consequently suggesting that the source of mixed crustal Pb is mainly derived from basement rocks. Combined with the initial 87Sr/86Sr ratios of sphalerite between the (87Sr/86Sr)200Ma value of the basement rocks and that of the Upper Sinian–Permian carbonates, it can be concluded that the ore-forming metals were mainly derived from basement rocks. Third, sulfur isotopic composition of sphalerite from the Laoyingqing deposits shows δ34SCDT values that range mainly from -2.62‰ to 1.42‰, which is evidently lower than the δ34SCDT values of sulfides (8–20‰) from other Pb–Zn deposits in the SYGT. This can be interpreted as a result of mixing with reduced S that was mainly derived from the thermochemically reduced S in the overlying strata and a small amount of reduced S produced by the pyrolysis of S-containing organic matter. We conclude that the Laoyingqing deposit and most of the Pb–Zn deposits in the SYGT are Mississippi Valley-type deposits, thereby providing new ideas for investigating the deep and peripheral areas of Pb–Zn deposits.

The Maliping large-scale Pb-Zn deposit is located in the Sichuan-Yunnan-Guizhou Pb-Zn polymetallic metallogenic triangle area (SYGT), where the Pb-Zn ore body is hosted in the interlayer fracture zone at the interface between siliceous cataclastic dolomite and clastic rocks in the Lower Cambrian Yuhuchun Formation and is tectonically driven. Unlike other Pb-Zn de-posits hosted in the Sinian and Carboniferous carbonate rocks in the area, the metallogenic mechanism and deep and peripheral ore prospecting prediction research require further exploration. In this study, representative samples of a typical orebody profile were systematically collected, and microthermometry of fluid inclusions and H-O isotopes and metal sulfide trace element analyses were performed. The main findings were as follows: (1) The fluid inclusion study showed that the ore-forming fluids have vapor-rich phase reduction characteristics of medium-low temperature, salinity, and density. (2) H-O isotopic studies showed that the ore-forming fluids are derived from the mixing of deep-source fluids flowing through the deep fold basement (Kunyang Group) and or-ganic-containing basin brine. (3) Rare earth element (REE) characteristics indicate that the ore-forming materials were primarily derived from the folded basement (Kunyang Group). (4) The trace element study showed that sphalerite is relatively enriched in Cu, Cd, Ga, and Ge, while depleted in Fe, Mn, Sn, and Co, similar to the typical Huize-type (HZT) Pb-Zn deposit in the area. Therefore, it is suitable to explore the deposit using a large-scale “four step style” ore prospecting method for ore prospecting and prediction. Moreover, the results provide a reference for the study of Pb-Zn metallogenic systems and new ideas for the deep and peripheral prospecting of Pb-Zn deposits in this area.

The seepage performance of a rock mass mainly depends on the rock fractures developed in it. Numerical calculation method is a common method to study the permeability properties of fractures. Seepage in rock fractures is affected by various factors such as fracture aperture, roughness, and filling, among which aperture and roughness are the two most widely influenced factors. The Navier-Stokes (NS) equation can be solved directly for the seepage flow in rock fractures with good accuracy, but there are problems of large computational volume and slow solution speed. In this paper, the fracture aperture space data is substituted into the local cubic law as an aperture function to form a numerical calculation method for seepage in rough rock fractures, namely, the aperture function method (AFM). Comparing with the physical seepage experiments of rock fractures, the calculation results of AFM will produce a small amount of error under the low Reynolds number condition, but it can greatly improve the calculation efficiency. The high efficiency of calculation makes it possible to apply AFM to the calculation of large-scale 3D rough fracture network models. The pressure drop of fluid in the fracture has viscous pressure drop (VPD) and local pressure drop (LPD). VPD can be calculated using the AFM. After analyzing the results of solving the NS equation for fracture seepage, it is concluded that the LPD includes the pressure drop caused by area crowding in the recirculation zone (RZ), kinetic energy loss in the RZ, kinetic energy loss in the vortices, and other reasons.

No abstract