To enhance and optimize nanocatalyst performance and durability for the oxygen reduction reaction in fuel-cell applications, we look beyond Pt-metal disordered alloys and describe a new class of Pt-Co nanocatalysts composed of ordered Pt(3)Co intermetallic cores with a 2-3 atomic-layer-thick platinum shell. These nanocatalysts exhibited over 200% increase in mass activity and over 300% increase in specific activity when compared with the disordered Pt(3)Co alloy nanoparticles as well as Pt/C. So far, this mass activity for the oxygen reduction reaction is the highest among the Pt-Co systems reported in the literature under similar testing conditions. Stability tests showed a minimal loss of activity after 5,000 potential cycles and the ordered core-shell structure was maintained virtually intact, as established by atomic-scale elemental mapping. The high activity and stability are attributed to the Pt-rich shell and the stable intermetallic Pt(3)Co core arrangement. These ordered nanoparticles provide a new direction for catalyst performance optimization for next-generation fuel cells.

No abstract

No abstract

A simple method for the preparation of PdCo@Pd core-shell nanoparticles supported on carbon based on an adsorbate-induced surface segregation effect has been developed. The stability of these PdCo@Pd nanoparticles and their electrocatalytic activity for the oxygen reduction reaction (ORR) were enhanced by decoration with a small amount of Pt deposited via a spontaneous displacement reaction. The facile method described herein is suitable for large-scale, lower-cost production and significantly lowers the Pt loading and thus the cost. The as-prepared PdCo@Pd and Pd-decorated PdCo@Pd nanocatalysts have a higher methanol tolerance than Pt/C in the ORR and are promising cathode catalysts for fuel cell applications.

Hydrogen energy-based electrochemical energy conversion technologies offer the promise of enabling a transition of the global energy landscape from fossil fuels to renewable energy. Here, we present a comprehensive review of the fundamentals of electrocatalysis in alkaline media and applications in alkaline-based energy technologies, particularly alkaline fuel cells and water electrolyzers. Anion exchange (alkaline) membrane fuel cells (AEMFCs) enable the use of nonprecious electrocatalysts for the sluggish oxygen reduction reaction (ORR), relative to proton exchange membrane fuel cells (PEMFCs), which require Pt-based electrocatalysts. However, the hydrogen oxidation reaction (HOR) kinetics is significantly slower in alkaline media than in acidic media. Understanding these phenomena requires applying theoretical and experimental methods to unravel molecularlevel thermodynamics and kinetics of hydrogen and oxygen electrocatalysis and, particularly, the proton-coupled electron transfer (PCET) process that takes place in a proton-deficient alkaline media. Extensive electrochemical and spectroscopic studies, on single-crystal Pt and metal oxides, have contributed to the development of activity descriptors, as well as the identification of the nature of active sites, and the rate-determining steps of the HOR and ORR. Among these, the structure and reactivity of interfacial water serve as key potential and pH-dependent kinetic factors that are helping elucidate the origins of the HOR and ORR activity differences in acids and bases. Additionally, deliberately modulating and controlling catalyst−support interactions have provided valuable insights for enhancing catalyst accessibility and durability during operation. The design and synthesis of highly conductive and durable alkaline membranes/ionomers have enabled AEMFCs to reach initial performance metrics equal to or higher than those of PEMFCs. We emphasize the importance of using membrane electrode assemblies (MEAs) to integrate the often separately pursued/optimized electrocatalyst/support and membranes/ionomer components. Operando/in situ methods, at multiscales, and ab initio simulations provide a mechanistic understanding of electron, ion, and mass transport at catalyst/ionomer/membrane interfaces and the necessary guidance to achieve fuel cell operation in air over thousands of hours. We hope that this Review will serve as a roadmap for advancing the scientific understanding of the fundamental factors governing electrochemical energy conversion in alkaline media with the ultimate goal of achieving ultralow Pt or precious-metal-free highperformance and durable alkaline fuel cells and related technologies.

The observed water oxidation activity of the compound class Co4O4(OAc)4(Py–X)4 emanates from a Co(II) impurity. This impurity is oxidized to produce the well-known Co-OEC heterogeneous cobaltate catalyst, which is an active water oxidation catalyst. We present results from electron paramagnetic resonance spectroscopy, nuclear magnetic resonance line broadening analysis, and electrochemical titrations to establish the existence of the Co(II) impurity as the major source of water oxidation activity that has been reported for Co4O4 molecular cubanes. Differential electrochemical mass spectrometry is used to characterize the fate of glassy carbon at water oxidizing potentials and demonstrate that such electrode materials should be used with caution for the study of water oxidation catalysis.

Identifying the catalytically active site(s) in the oxygen reduction reaction (ORR), under real-time electrochemical conditions, is critical to the development of fuel cells and other technologies. We have employed in situ synchrotron-based X-ray absorption spectroscopy (XAS) to investigate the synergistic interaction of a Co–Mn oxide catalyst which exhibits impressive ORR activity in alkaline fuel cells. X-ray absorption near edge structure (XANES) was used to track the dynamic structural changes of Co and Mn under both steady state (constant applied potential) and nonsteady state (potentiodynamic cyclic voltammetry, CV). Under steady state conditions, both Mn and Co valences decreased at lower potentials, indicating the conversion from Mn­(III,IV) and Co­(III) to Mn­(II,III) and Co­(II), respectively. Rapid X-ray data acquisition, combined with a slow sweep rate in CV, enabled a 3 mV resolution in the applied potential, approaching a nonsteady (potentiodynamic) state. Changes in the Co and Mn valence states were simultaneous and exhibited periodic patterns that tracked the cyclic potential sweeps. To the best of our knowledge, this represents the first study, using in situ XAS, to resolve the synergistic catalytic mechanism of a bimetallic oxide. Strategies developed/described herein can provide a promising approach to unveil the reaction mechanism for other multimetallic electrocatalysts.

Electrocatalysis has been the cornerstone for enhancing energy efficiency, minimizing environmental impacts and carbon emissions, and enabling a more sustainable way of meeting global energy needs. Elucidating the structure and reaction mechanisms of electrocatalysts at electrode–electrolyte interfaces is fundamental for advancing renewable energy technologies, including fuel cells, water electrolyzers, CO2 reduction, and batteries, among others. One of the fundamental challenges in electrocatalysis is understanding how to activate and sustain electrocatalytic activity, under operating conditions, for extended time periods and with optimal activity and selectivity. Although traditional ex situ methods have provided a baseline understanding of heterogeneous (electro)­catalysts, they cannot provide real-time interfacial structural and compositional changes under reaction conditions, which calls for the use of in situ/operando methods. Herein, we provide a selective review of in situ and operando characterizations, in particular, the use of operando synchrotron-based X-ray techniques and in situ atomic-scale scanning transmission electron microscopy (STEM) in liquid/gas phases to advance our understanding of electrode–electrolyte interfaces at macro- and microscopic levels, which dictate the charge transfer kinetics and overall reaction mechanisms. The use of scanning electrochemical microscopy (SECM) enables direct probing of the local activity of electrocatalysts at the nanometer scale. In addition, differential electrochemical mass spectrometry (DEMS) and the electrochemical quartz crystal balance (EQCM) enable the simultaneous identification of multiple reaction intermediates and products for mechanistic studies of electrocatalyst selectivity and durability. We anticipate that continuous advances of in situ/operando techniques and probes will continue to make significant contributions to establishing structure/composition-reactivity correlations of electrocatalysts at unprecedented atomic-scale and molecular levels under realistic, real-time reaction conditions.