1 wileyonlinelibrary.com recoverability and self-healing property, due to their intrinsic structural heterogeneity and/or lack of effi cient energydissipation mechanisms, [ 13 ] which greatly limit their uses for other applications requiring highly mechanical properties such as cartilage, tendon, muscle, and blood vessel.Many efforts have been made to develop tough hydrogels with new microstructures and toughening mechanisms, such as double network hydrogels, [ 14 ] nanocomposite hydrogels, [ 15 ] sliding-ring hydrogels, [ 16 ] macromolecular microsphere composite hydrogels, [ 17 ] tetrapolyethylene glycol hydrogels, [ 18 ] hydrophobically associated hydrogels, [ 19,20 ] and dipole-dipole or hydrogen bonding enhanced hydrogels. [ 21,22 ] Among them, double network (DN) hydrogels have demonstrated their excellent mechanical properties. The existing knowledge of DN gels from synthesis methods, network structures, to toughening mechanisms mainly comes from chemically cross-linked DN gels. [ 23 ] Both networks with contrasting structures in DN gels are separately crosslinked by covalent bonds, [ 24 ] and the interpenetration of two contrasting networks makes the chemically linked DN gels both tough and soft, as evidenced by stiffness (elastic modulus of 0.1-1.0 MPa), strength (failure tensile stress of 1-10 MPa, strain 1000%-2000%, failure compressive stress 20-60 MPa, strain 90%-95%), and toughness (tearing fracture energy of 10 2 -10 3 J m −2 ). [ 23 ] Chemically linked DN gels have comparable toughness to cartilage and rubber. The toughening mechanisms are largely based on "sacrifi cial bonds" that break from the fi rst network to effectively dissipate energy, protect the second network, sustain stress, and store elastic energy, thus to reinforce the gels. However, the fracture of the fi rst network also causes irreversible and permanent bond breaks, making the gels very diffi cult to be repaired and recovered from damages and fatigues. [ 25 ] Thus, the internal fracture process of the fi rst network is considered to be critical for toughness enhancement, because relatively large damage zones formed in the fi rst network allow for more accumulated damage before macroscopic crack propagation occurs throughout whole networks. [ 26,27 ] Double network (DN) hydrogels with two strong asymmetric networks being chemically linked have demonstrated their excellent mechanical properties as the toughest hydrogels, but chemically linked DN gels often exhibit negligible fatigue resistance and poor self-healing property due to the irreversible chain breaks in covalent-linked networks. Here, a new design strategy is proposed and demonstrated to improve both fatigue resistance and self-healing property of DN gels by introducing a ductile, nonsoft gel with strong hydrophobic interactions as the second network. Based on this design strategy, a new type of fully physically cross-linked Agar/hydrophobically associated polyacrylamide (HPAAm) DN gels are synthesized by a simple one-pot method. Agar/ HPAAm DN gels exhibit excellent mech...

Genetically encoded protein scaffolds often serve as templates for the mineralization of biocomposite materials with complex yet highly controlled structural features that span from nanometres to the macroscopic scale. Methods developed to mimic these fabrication capabilities can produce synthetic materials with well defined micro- and macro-sized features, but extending control to the nanoscale remains challenging. DNA nanotechnology can deliver a wide range of customized nanoscale two- and three-dimensional assemblies with controlled sizes and shapes. But although DNA has been used to modulate the morphology of inorganic materials and DNA nanostructures have served as moulds and templates, it remains challenging to exploit the potential of DNA nanostructures fully because they require high-ionic-strength solutions to maintain their structure, and this in turn gives rise to surface charging that suppresses the material deposition. Here we report that the Stöber method, widely used for producing silica (silicon dioxide) nanostructures, can be adjusted to overcome this difficulty: when synthesis conditions are such that mineral precursor molecules do not deposit directly but first form clusters, DNA-silica hybrid materials that faithfully replicate the complex geometric information of a wide range of different DNA origami scaffolds are readily obtained. We illustrate this approach using frame-like, curved and porous DNA nanostructures, with one-, two- and three-dimensional complex hierarchical architectures that range in size from 10 to 1,000 nanometres. We also show that after coating with an amorphous silica layer, the thickness of which can be tuned by adjusting the growth time, hybrid structures can be up to ten times tougher than the DNA template while maintaining flexibility. These findings establish our approach as a general method for creating biomimetic silica nanostructures.

Sodium-ion batteries (SIBs) are still confronted with several major challenges, including low energy and power densities, short-term cycle life, and poor low-temperature performance, which severely hinder their practical applications. Here, a high-voltage cathode composed of Na V (PO ) O F nano-tetraprisms (NVPF-NTP) is proposed to enhance the energy density of SIBs. The prepared NVPF-NTP exhibits two high working plateaux at about 4.01 and 3.60 V versus the Na /Na with a specific capacity of 127.8 mA h g . The energy density of NVPF-NTP reaches up to 486 W h kg , which is higher than the majority of other cathode materials previously reported for SIBs. Moreover, due to the low strain (≈2.56% volumetric variation) and superior Na transport kinetics in Na intercalation/extraction processes, as demonstrated by in situ X-ray diffraction, galvanostatic intermittent titration technique, and cyclic voltammetry at varied scan rates, the NVPF-NTP shows long-term cycle life, superior low-temperature performance, and outstanding high-rate capabilities. The comparison of Ragone plots further discloses that NVPF-NTP presents the best power performance among the state-of-the-art cathode materials for SIBs. More importantly, when coupled with an Sb-based anode, the fabricated sodium-ion full-cells also exhibit excellent rate and cycling performances, thus providing a preview of their practical application.

For the first time, organic semiconducting polymer dots (Pdots) based on poly[(9,9'-dioctylfluorenyl-2,7-diyl)-co-(1,4-benzo-{2,1',3} thiadiazole)] (PFBT) and polystyrene grafting with carboxyl-group-functionalized ethylene oxide (PS-PEG-COOH) are introduced as a photocatalyst towards visible-light-driven hydrogen generation in a completely organic solvent-free system. With these organic Pdots as the photocatalyst, an impressive initial rate constant of 8.3 mmol h(-1)  g(-1) was obtained for visible-light-driven hydrogen production, which is 5-orders of magnitude higher than that of pristine PFBT polymer under the same catalytic conditions. Detailed kinetics studies suggest that the productive electron transfer quench of the excited state of Pdots by an electron donor is about 40 %. More importantly, we also found that the Pdots can tolerate oxygen during catalysis, which is crucial for further application of this material for light-driven water splitting.

Vacancy-rich layered materials with good electron-transfer property are of great interest. Herein, a full-spectrum responsive vacancy-rich monolayer BiO has been synthesized. The increased density of states at the conduction band (CB) minimum in the monolayer BiO is responsible for the enhanced photon response and photo-absorption, which were confirmed by UV/Vis-NIR diffuse reflectance spectra (DRS) and photocurrent measurements. Compared to bulk BiO , monolayer BiO has exhibited enhanced photocatalytic performance for rhodamine B and phenol removal under UV, visible, and near-infrared light (NIR) irradiation, which can be attributed to the vacancy V ''' as confirmed by the positron annihilation spectra. The presence of V ''' defects in monolayer BiO promoted the separation of electrons and holes. This finding provides an atomic level understanding for developing highly efficient UV, visible, and NIR light responsive photocatalysts.

Two-dimensional (2D) Sn-based perovskites are a kind of non-toxic environment-friendly luminescent material. However, the research on the luminescence mechanism of this type of perovskite is still very controversial, which greatly limits the further improvement and application of the luminescence performance. At present, the focus of controversy is defects and phonon scattering rates. In this work, we combine the organic cation control engineering with temperature-dependent transient absorption spectroscopy to systematically study the interband exciton relaxation pathways in layered A2SnI4 (A = PEA+, BA+, HA+, and OA+) structures. It is revealed that exciton-phonon scattering and exciton-defect scattering have different effects on exciton relaxation. Our study further confirms that the deformation potential scattering by charged defects, not by the non-polar optical phonons, dominates the excitons interband relaxation, which is largely different from the Pb-based perovskites. These results enhance the understanding of the origin of the non-radiative pathway in Sn-based perovskite materials.

Two-dimensional (2D) perovskites, with a formula of (RNH)MA PbI, have shown impressive photovoltaic device efficiency with improved stability. The operating mechanism of such photovoltaic devices is under debate and the scope of incorporated organic cations (RNH) is limited. We report a general post-annealing method to incorporate a variety of organic cations into 2D perovskites, which demonstrate significant device efficiencies (7-12%). A detailed investigation of the archetypical (CHNH)MAPbI ( n = 4) reveals that such perovskites thin films contain multiple 2D phases (i.e., 2D quantum wells, n = 2, 3, 4, ...). These phases appear to be distributed with decreasing n values from the top to the bottom of the 2D perovskites thin film, enabling efficient energy transfer in the first 500 ps and possible charge transfer at longer time scale, thereby accounting for high device efficiencies. Our post-annealing method is compatible with ambient condition and only requires relatively low annealing temperature for a very short period of time, offering significant prospects for scalable manufacturing of 2D perovskites solar cells.

Recently, reactive iron species (RFeS) have shown great potential for the selective degradation of emerging organic contaminants (EOCs). However, the rapid generation of RFeS for the selective and efficient degradation of EOCs over a wide pH range is still challenging. Herein, we constructed FeN4 structures on a carbon nanotube (CNT) to obtain single-atom catalysts (FeSA-N-CNT) to generate RFeS in the presence of peroxymonosulfate (PMS). The obtained FeSA-N-CNT/PMS system exhibited outstanding and selective reactivity for oxidizing EOCs over a wide pH range (3.0–9.0). Several lines of evidences suggested that RFeS existing as an FeN4O intermediate was the predominant oxidant, while SO4 ·– and HO· were the secondary oxidants. Density functional theory calculation results revealed that a CNT played a key role in optimizing the distribution of bonding and antibonding states in the Fe 3d orbital, resulting in the outstanding ability of FeSA-N-CNT for PMS chemical adsorption and activation. Moreover, CNT could significantly enhance the reactivity of the FeN4O intermediate by increasing the overlap of electrons of the Fe 3d orbital, O 2p orbital, and bisphenol A near the Fermi level. The results of this study can advance the understanding of RFeS generation in a heterogeneous system over a wide pH range and the application of RFeS in real practice.