A new Schiff base was prepared as the condensation product of the reaction of 2‐quinoline carboxaldehyde and ambroxol drug. The Schiff base ligand thus obtained (HL; trans‐4‐[(2‐(2‐quinolinoimino)‐3,5‐dibromobenzyl)amino]cyclohexanol) was further employed as a tridentate ligand for the synthesis of new complexes through reaction with Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II) and Cd(II) metal ions. The synthesized HL and its metal complexes were characterized using various physicochemical techniques including elemental analysis, Fourier transform infrared and UV–visible spectroscopies, conductimetric and magnetic susceptibility measurements, mass spectrometry and thermal analyses. 1H NMR data indicated that complex formation was through the amino group rather than the aliphatic hydroxyl group. Thermal analysis gave an idea about the decomposition pattern of HL and its complexes. Also, it revealed the number of water molecules in the inner and outer spheres of the complexes. An octahedral geometry for all the complexes has been suggested. HL and its complexes were screened for their antimicrobial activity against various species of bacteria and fungi using the disc diffusion method. The Cr(III) complex had the highest antimicrobial activity.
In this study, the hydroxyapatite powder is investigated for both of methylene blue and thymol blue in aqueous solution. The physical and chemical properties of the adsorbent were evaluated systematically using the different techniques including Microsoft Excel programming, linear regression model and also the coefficient of determination. Batch adsorption experiments were conducted to determine the effect of contact time, solution pH, initial dye concentrations, and also the adsorbent dosage on adsorption. The adsorption kinetic parameters confirmed the better fitting of pseudo-second order kinetic model for both of methylene blue and thymol blue. The isotherm data of methylene blue and thymol blue could be well described by the Freundlich isotherm model which means the adsorption is multilayer adsorption with non-uniform distribution of adsorption heat and affinities over the heterogeneous surface. The maximum adsorption capacity (KF) of methylene blue and thymol blue is found to be 0.2736 (L/mg) and 11.18407 (L/mg) respectively. The high specific surface area and the porous structure with some acidic functional groups on the surface were obviously responsible for high dyes adsorption onto hydroxyapatite (HA). Adsorption kinetics data were modeled with the application of Pseudo first order, Pseudo second order and Intraparticle diffusion models. The results revealed that the Pseudo second order model was the best fitting model. Which means that, the adsorption mechanism followed two stages in which the first one was fast and the other was slower step. Which means the adsorption of dye molecules was limited by intra particle diffusion and film diffusion, as well as, the adsorption rate in both of adsorption system are depends only on the slower step.The Boyd plot exposed that the intra-particle diffusion was the rate controlling step of the adsorption process of both of methylene blue and thymol blue molecules by HA powder. However, the adsorption of methylene blue molecules (basic solution) using of HA as adsorbent particles is found to be extremely preferable than thymol blue molecules.
Water is the most important resource for life, but it has been greatly exhausted over the past century as a result of the human population and environmentally harmful activities. The excessive quantity of dyes exists in the wastewater produced from the textile industries which is the main reason for serious human health and environmental problems. There are many dye removal techniques, and the most promising one is the adsorption technique. The novelty of this research is using unmodified synthesized hydroxyapatite (HAp) as an adsorbent for the removal of gentian violet (GV) dye from aqueous solutions as there are no sufficient data in the literature about using it in the adsorption of GV dye from aqueous solutions. Unmodified HAp was synthesized by a combined precipitation microwave method. The prepared adsorbent was characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and zeta potential analyses. The kinetic study showed that the pseudo-second-order (PSO) model was the best fitted model with the experimental data. Analysis of adsorption isotherms using different models showed that this adsorption system was better described by the Halsey isotherm with a maximum adsorption capacity (qmax) of 1.035 mg/g. The effects of experimental factors such as initial solution pH, initial dye concentration, adsorbent dose, and contact time were studied during the investigation of GV dye removal efficiency. The experimental results indicated that the maximum adsorption efficiency (99.32%) of the GV dye using HAp adsorbent was achieved at the following conditions: contact time = 90 min, pH = 12, initial GV dye concentration = 3 mg/L, and adsorbent dose = 1 g/L. The adsorption mechanism of the GV dye using HAp might be explained by the electrostatic interaction between the negatively charged surface of the HAp and the positively charged group of the GV dye. Thermodynamics study was performed on the adsorption process of GV dye from aqueous solutions using the synthesized HAp which revealed that this process was endothermic and spontaneous due to positive values of ΔH and ΔS and negative values of ΔG.
Excessive amount of dyes in the discharged wastewater from the textile industry becomes a severe problem in water pollution due to the presence of unruly toxic organic compounds. Dyes are highly toxic and carcinogenic compounds that cause extremely harmful effects on the on the human health. The adsorption method is considered one of the best methods for dye removal from wastewater because of its availability, low cost, stability, large surface area to volume ratio and high adsorption capacity. In this article, hydroxyapatite (HAP) was used as a solid adsorbent for the removal of methyl orange (MO) dye from aqueous solutions. Fourier Transform Infrared (FTIR) surface characterization test was performed before and after the adsorption process, ensuring the adsorption of the MO dye successfully using HAP. Adsorption kinetics and isotherms were studied for this adsorption system to predict the adsorption mechanism. Additionally, the effects of changing pH of solution, initial MO dye concentration, of adsorbent dose and contact time on the adsorption process efficiency were studied. The maximum adsorption efficiency for MO dye from aqueous solutions (88.3%) was achieved at the optimum operating conditions of contact time = 90 min, pH = 4, initial dye concentration = 0.5 mg/L and adsorbent dose = 2 g/L.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.