No abstract

No abstract

Extreme ultraviolet lithography (EUVL, λ ¼ 13.5 nm) is the most promising candidate to manufacture electronic devices for future technology nodes in the semiconductor industry. Nonetheless, EUVL still faces many technological challenges as it moves toward high-volume manufacturing (HVM). A key bottleneck from the tool design and performance point of view has been the development of an efficient, high-power EUV light source for high throughput production. Consequently, there has been extensive research on different methodologies to enhance EUV resist sensitivity. Resist performance is measured in terms of its ultimate printing resolution, line width roughness (LWR), sensitivity [S or best energy (BE)], and exposure latitude (EL). However, there are well-known fundamental trade-off relationships (line width roughness, resolution and sensitivity tradeoff) among these parameters for chemically amplified resists (CARs). We present early proof-of-principle results for a multiexposure lithography process that has the potential for high sensitivity enhancement without compromising other important performance characteristics by the use of a "Photosensitized Chemically Amplified Resist ™ " (PSCAR ™ ). With this method, we seek to increase the sensitivity by combining a first EUV pattern exposure with a second UV-flood exposure (λ ¼ 365 nm) and the use of a PSCAR. In addition, we have evaluated over 50 different state-of-the-art EUV CARs. Among these, we have identified several promising candidates that simultaneously meet sensitivity, LWR, and EL high-performance requirements with the aim of resolving line space (L/S) features for the 7-and 5-nm logic node , respectively] for HVM. Several CARs were additionally found to be well resolved down to 12-and 11-nm HP with minimal pattern collapse and bridging, a remarkable feat for CARs. Finally, the performance of two negative tone state-of-the-art alternative resist platforms previously investigated was compared to the CAR performance at and below 16-nm HP resolution, demonstrating the need for alternative resist solutions at 13-nm resolution and below. EUV interference lithography (IL) has provided and continues to provide a simple yet powerful platform for academic and industrial research, enabling the characterization and development of resist materials before commercial EUV exposure tools become available. Our experiments have been performed at the EUV-IL set-up in the Swiss Light Source (SLS) synchrotron facility located at the Paul Scherrer Institute (PSI).

Ultra low-k porous (k = 2.4) materials are currently used for microelectronic applications. Future device generations require even lower dielectric constants, i.e. higher porosity. For highly porous systems, processing damage and mechanical properties are of great concern. Regarding the latter, sol-gel derived, spin-on oxycarbosilane homopolymers exhibit significantly higher stiffness and fracture resistance as compared to traditional organosilicates. Unfortunately, traditional sol-gel formulations show poor long-term solution stability. This presents a serious limitation to their use in manufacturing. In this paper, we describe the development of a stable, manufacturing grade spin-on formulation (k = 2.0) that meets all the other integration requirements.

Extreme ultraviolet lithography (EUVL, λ = 13.5 nm) is the most promising candidate to manufacture electronic devices for future technology nodes in the semiconductor industry. Nonetheless, EUVL still faces many technological challenges as it moves toward high-volume manufacturing (HVM). A key bottleneck from the tool design and performance point of view has been the development of an efficient, high power EUV light source for high throughput production. Consequently, there has been extensive research on different methodologies to enhance EUV resist sensitivity. Resist performance is measured in terms of its ultimate printing resolution, line width roughness (LWR), sensitivity (S or best energy BE) and exposure latitude (EL). However, there are well-known fundamental trade-off relationships (LRS trade-off) among these parameters for chemically amplified resists (CARs). Here we present early proof-of-principle results for a multi-exposure lithography process that has the potential for high sensitivity enhancement without compromising other important performance characteristics by the use of a Photosensitized Chemically Amplified Resist TM (PSCAR TM). With this method, we seek to increase the sensitivity by combining a first EUV pattern exposure with a second UV flood exposure (λ = 365 nm) and the use of a PSCAR. In addition, we have evaluated over 50 different state-of-the-art EUV CARs. Among these, we have identified several promising candidates that simultaneously meet sensitivity, LWR and EL high performance requirements with the aim of resolving line space (L/S) features for the 7 and 5 nm logic node (16 nm and 13 nm half-pitch HP, respectively) for HVM. Several CARs were additionally found to be well resolved down to 12 nm and 11 nm HP with minimal pattern collapse and bridging, a remarkable feat for CARs. Finally, the performance of two negative tone state-of-the-art alternative resist platforms previously investigated was compared to the CAR performance at and below 16 nm HP resolution, demonstrating the need for alternative resist solutions at 13 nm resolution and below. EUV interference lithography (IL) has provided and continues to provide a simple yet powerful platform for academic and industrial research enabling the characterization and development of new resist materials before commercial EUV exposure tools become available. Our experiments have been performed at the EUV-IL setup in the Swiss Light Source (SLS) synchrotron facility located at the Paul Scherrer Institute (PSI).

We have investigated the transition phenomena of superfluid 3He in thin 0.8 microm slabs with a cw-NMR method. We found that, just below the phase-transition temperature, only the A phase appeared at any pressure. At lower temperatures, the phase transition to the B phase occurred between 0.3 and 2.74 MPa. We obtained a universal critical thickness delta as a function of pressure. When the reduced slab thickness, d/xi(T), is smaller than delta, only the A phase becomes stable.

Extreme ultraviolet (EUV) lithography has emerged as a promising candidate for the manufacturing of semiconductor devices at the sub-14nm half pitch lines and spaces (LS) pattern for 7 nm node and beyond. The success of EUV lithography for the high volume manufacturing of semiconductor devices depends on the availability of suitable resist with high resolution and sensitivity. It is well-known that the key challenge for EUV resist is the simultaneous requirement of ultrahigh resolution (R), low line edge roughness (L) and high sensitivity (S). In this paper, we investigated and developed new chemically amplified resist (CAR) materials to achieve sub-14 nm hp resolution. We found that both resolution and sensitivity were improved simultaneously by controlling acid diffusion length and efficiency of acid generation using novel PAG and sensitizer. EUV lithography evaluation results obtained for new CAR on Micro Exposure Tool (MET) and NXE3300 system are described and the fundamentals are discussed.

Extreme ultraviolet lithography (EUVL) has been an attractive method as next generation lithography (NGL) over 20 years, and high-volume manufacturing (HVM) is now going to be realized by great progresses in materials as well as EUV source power enhancement. In this paper, recent reported materials for EUVL are summarized ranging from conventional organic material base resists to novel inorganic material base resists.