Remote control of the locomotion of small objects is a challenge in itself and may also allow for the stimuli control of entire systems. Here, it is described how encapsulated liquids, referred to as liquid marbles, can be moved on a water surface with a simple near‐infrared laser or sunlight. Using light rather than pH or temperature as an external stimulus allows for the control of the position, area, timing, direction, and velocity of delivery. This approach makes it possible to not only transport the materials encapsulated within the liquid marble but also to release them at a specific place and time, as controlled by external stimuli. Furthermore, it is shown that liquid marbles can work as light‐driven towing engines to push or pull objects. Being able to remotely transport and push/pull the small objects by light and control the release of active substances on demand should open up a wide field of conceivable applications.

Theoretical study is presented on the wetting behaviors of water droplets over a lotus leaf. Experimental results are interpreted to clarify the trade-offs among the potential energy change, the local pinning energy, and the adhesion energy. The theoretical parameters, calculated from the experimental results, are used to qualitatively explain the relations among surface fractal dimension, surface morphology, and dynamic wetting behaviors. The surface of a lotus leaf, which shows the superhydrophobic lotus effect, was dipped in ethanol to remove the plant waxes. As a result, the lotus effect is lost. The contact angle of a water drop decreased dramatically from 161° of the original surface to 122°. The water droplet was pinned on the surface. From the fractal analysis, the fractal region of the original surface was divided into two regions: a smaller-sized roughness region of 0.3-1.7 μm with D of 1.48 and a region of 1.7-19 μm with D of 1.36. By dipping the leaf in ethanol, the former fractal region, characterized by wax tubes, was lost, and only the latter large fractal region remained. The lotus effect is attributed to a surface structure that is covered with needle-shaped wax tubes, and the remaining surface allows invasion of the water droplet and enlarges the interaction with water.

Repellent films: Poly(alkylpyrrole) conductive films with a water contact angle larger than 150° are stable to temperature, organic solvents, and oils and are super water‐repellent. The surface of the film is a fractal and consists of an array of perpendicular needle‐like structures (see picture; inset: digital camera image of a water droplet on the film).

Remotely controlling the movement of small objects is desirable, especially for the transportation and selection of materials. Transfer of objects between liquid and solid surfaces and triggering their release would allow for development of novel material transportation technology. Here, we describe the remote transport of a material from a water film surface to a solid surface using quasispherical liquid marbles (LMs). A light-induced Marangoni flow or an air stream is used to propel the LMs on water. As the LMs approach the rim of the water film, gravity forces them to slide down the water rim and roll onto the solid surface. Through this method, LMs can be efficiently moved on water and placed on a solid surface. The materials encapsulated within LMs can be released at a specific time by an external stimulus. We analyzed the velocity, acceleration, and force of the LMs on the liquid and solid surfaces. On water, the sliding friction due to the drag force resists the movement of the LMs. On a solid surface, the rolling distance is affected by the surface roughness of the LMs.

Alkylketene dimer (AKD), a kind of wax, has been known to form fractal surfaces spontaneously and show super water-repellency. Such formation of water-repellent and fractal surfaces was also found in this work for triglycerides. Since the crystal phase transitions of these waxes were well studied, we studied the formation of their fractal surfaces through contact angle measurements, differential scanning calorimetry (DSC), and X-ray diffraction (XRD). From time-dependent contact angle measurements, it was found that the formation of super water-repellent surfaces with fractal structures occurred spontaneously also on the triglyceride surfaces at different temperatures. The freshly solidified triglyceride surfaces were almost transparent, and their initial contact angles of water were close to 110 degrees. The surfaces then became rough and clouded after being incubated for a certain time at a specified temperature. The super water-repellent surfaces were quite rough and showed fractal structures with the dimension of ca. 2.2 calculated from the scanning electron microscopic (SEM) images by the box-counting method. The phase transformation from a metastable state to a stable cystalline one after the solidification from the melt of triglycerides was clearly observed by DSC and XRD measurements. The fractal crystalline structures and the super water-repellency resulted from this phase transformation and the crystal growth. Ensuring the initial sample solidified into the metastable state and curing the surface at an appropriate temperature are key factors for the successful preparation of fractal triglyceride surfaces by the solidification method.

Hydrophobic polypyrroles doped with perfluoroalkyl dopants can function as a liquid marble stabilizer with photothermal properties.

By alternate UV and visible light irradiation, reversible topographical changes were observed on a newly synthesized diarylethene microcrystalline surface between the rough crystalline surface of an open-ring isomer and flat eutectic surfaces. The contact angle changes of a water droplet between 80° and 150° and peak intensities changes of the open-ring isomer in XRD patterns within 2 h of repeating cycle were observed. The results indicated that reversibly photogenerated rod-shaped crystals on the surface were produced based on the lattice of the open-ring isomer crystals in the subphase.

Double roughness structure, the origin of the lotus effect of natural lotus leaf, was successfully reproduced on a diarylethene microcrystalline surface. Static superwater-repellency and dynamic water-drop-bouncing were observed on the surface, in the manner of natural lotus leaves. Double roughness structure was essential for water-drop-bouncing. This ability was not observed on a single roughness microcrystalline surface showing the lotus effect of the same diarylethene derivative. The double roughness structure was reversibly controlled by alternating irradiation with UV and visible light.