Artificial planar lipid bilayers are a powerful tool for the functional study of membrane proteins, yet they have not been widely used due to their low stability and reproducibility. This paper describes an accessible method to form a planar lipid bilayer, simply by contacting two monolayers assembled at the interface between water and organic solvent in a microfluidic chip. The membrane of an organic solvent containing phospholipids at the interface was confirmed to be a bilayer by the capacitance measurement and by measuring the ion channel signal from reconstituted antibiotic peptides. We present two different designs for bilayer formation. One equips two circular wells connected, in which the water/solvent/water interface was formed by simply injecting a water droplet into each well. Another equips the cross-shaped microfluidic channel. In the latter design, formation of the interface at the sectional area was controlled by external syringe pumps. Both methods are extremely simple and reproducible, especially in microdevices, and will lead to automation and multiple bilayer formation for the high-throughput screening of membrane transport in physiological and pharmaceutical studies.

Mechanisms that enabled primitive cell membranes to self-reproduce have been discussed based on the physicochemical properties of fatty acids; however, there must be a transition to modern cell membranes composed of phospholipids [Budin I, Szostak JW (2011) Proc Natl Acad Sci USA 108:5249–5254]. Thus, a growth-division mechanism of membranes that does not depend on the chemical nature of amphiphilic molecules must have existed. Here, we show that giant unilamellar vesicles composed of phospholipids can undergo the coupled process of fusion and budding transformation, which mimics cell growth and division. After gaining excess membrane by electrofusion, giant vesicles spontaneously transform into the budded shape only when they contain macromolecules (polymers) inside their aqueous core. This process is a result of the vesicle maximizing the translational entropy of the encapsulated polymers (depletion volume effect). Because the cell is a lipid membrane bag containing highly concentrated biopolymers, this coupling process that is induced by physical and nonspecific interactions may have a general importance in the self-reproduction of the early cellular compartments.

Lipid vesicles have been used as model cell systems, in which an in-vitro transcription-translation system (IVTT) is encapsulated to carry out intravesicular protein synthesis. Despite a large number of previous studies, a quantitative understanding of how protein synthesis inside the vesicles is affected by the lipid membrane remains elusive. This is mainly because of the heterogeneity in structural properties of the lipid vesicles used in the experiments. We investigated the effects of the phospholipid membrane on green fluorescent protein (GFP) synthesis occurring inside cell-sized giant unilamellar vesicles (GUV), which have a defined quantity of lipids relative to the reaction volume. We first developed a method to distinguish GUV from multilamellar vesicles using flow cytometry (FCM). Using this method, we investigated the time course of GFP synthesis using one of the IVTT, the PURE system, and found that phospholipid in the form of GUV has little effect on GFP synthesis based on three lines of investigation. (1) GFP synthesis inside the GUV was not dependent on the size of GUV (2) or on the fraction of cholesterol or anionic phospholipid constituting the GUV, and (3) GFP synthesis proceeded similarly in GUV and in the test tube. The present results suggest that GUV provides an ideal reaction environment that does not affect the internal biochemical reaction. On the other hand, we also found that internal GFP synthesis is strongly dependent on the chemical composition of the outer solution.

We used fluorescence flow cytometry to analyze the structural properties of populations of giant liposomes formed by different preparation methods. The inner aqueous volumes and nominal membrane surface areas of a large number of individual liposomes were measured simultaneously by using fluorescent markers. We compared these properties of liposomes prepared by the natural swelling method, the freeze-dried empty liposomes method, and the water-in-oil (W/O) emulsion method. A two-dimensional contour distribution map of the inner volume and the nominal surface area was used to elucidate the structural properties of liposomes over a wide range of liposome sizes. Lamellarity of liposomes was evaluated as the ratio of the nominal surface area to the theoretical surface area calculated from the liposome inner volume. This population analysis revealed the dependency of lamellarity on liposome volume: while the nominal surface areas of populations of liposomes prepared by the natural swelling and the freeze-dried empty liposome methods were widely distributed, those prepared by the W/O emulsion method had a narrower distribution within small values. Furthermore, with the latter method, the nominal surface area varied in proportion to the two-thirds power of the inner volume ranging for several orders of magnitude, indicating the liposomes had a thin membrane, which was constant for the wide volume range. The results as well as the methodology presented here would be useful in designing giant liposomes with desired properties.

The Urban Development Series discusses the challenge of urbanization and what it will mean for developing countries in the decades ahead. The Series aims to delve substantively into the core issues framed by the World Bank's 2009 Urban Strategy, Systems of Cities: Harnessing Urbanization for Growth and Poverty Alleviation. Across the five domains of the Urban Strategy, the Series provides a focal point for publications that seek to foster a better understanding of the core elements of the city system, pro-poor policies, city economies, urban land and housing markets, sustainable urban environment, and other issues germane to the urban development agenda.

No abstract

No abstract

We developed a highly reproducible method for planar lipid bilayer reconstitution using a microfluidic system made of a polymethyl methacrylate (PMMA) plastic substrate. Planar lipid bilayers are formed at apertures, 100 microm in diameter, by flowing lipid solution and buffer alternately into an integrated microfluidic channel. Since the amount and distribution of the lipid solution at the aperture determines the state of the lipid bilayer, controlling them precisely is crucial. We designed the geometry of the fluidic system so that a constant amount of lipid solution is distributed at the aperture. Then, the layer of lipid solution was thinned by applying an external pressure and finally became a bilayer when a pressure of 200-400 Pa was applied. The formation process can be simultaneously monitored with optical and electrical recordings. The maximum yield for bilayer formation was 90%. Using this technique, four lipid bilayers are formed simultaneously in a single chip. Finally, a channel current through gramicidin peptide ion channels was recorded to prove the compatibility of the chip with single molecule electrophysiology.