Failure Mode and Effect Analysis (FMEA) banyak diimplementasikan untuk analisis risiko baik di bidang manufaktur maupun jasa. Permasalahan yang sering timbul pada implementasi FMEA yaitu sulitnya menentukan peringkat risiko karena kesamaan nilai RPN. Samanya nilai RPN menimbulkan kesulitan bagi pengambil keputusan untuk memprioritisasi risiko yang harus ditindaklanjuti. Logika fuzzy merupakan logika matematis yang dapat digunakan untuk memperbaiki kelemahan FMEA. Sehingga, tujuan penelitian ini adalah integrasi FMEA dengan logika fuzzy sebagai upaya perbaikan terhadap metode FMEA. Tujuan lainnya adalah implementasi integrasi Fuzzy-FMEA pada lingkup pengujian suhu lemari es. Implementasi Fuzzy-FMEA pada pengujian ini dilakukan sebagai tindakan pencegahan terhadap risiko kegagalan pada pengujian yang dipersyaratkan oleh SNI ISO/IEC 17025:2008. Studi kasus pengujian suhu pada lemari es ini dipilih karena lemari es merupakan salah satu produk yang diwajibkan untuk memperoleh Sertifikat Produk Penggunaan Tanda SNI (SPPT-SNI) yang mengacu pada standar SNI IEC 60335-2-7:2009. Selain itu, penerapan Fuzzy-FMEA pada konteks pengujian sampai saat ini belum ditemukan. Hasil analisis dengan Fuzzy-FMEA menunjukkan bahwa risiko kegagalan paling tinggi pada proses pengujian suhu lemari es paling tinggi terjadi pada mode kegagalan: power source tibatiba shut down dengan nilai RPN 5,8887.
ABSTRACT The purpose of this research is to know about the effect of current rate increasing and ambient temperature change on tripping time miniature circuit breakers 6A type C. In this research using an experimental method approach with the quantitative method. The research subject used five samples new miniature circuit breakers produced by Asian and European brand. The research data collection is carried out by testing using PLN voltage source, linier load and temperature change on chamber to know five samples miniature circuit breakers characteristics tripping time refer to SPLN 108:1993. The research result showed that, current rate increasing to ± 2.55 In and ambient temperature change have an effect on five samples miniature circuit breakers characteristics tripping time, where on reference temperature, different characteristics tripping time for each other however were still within the standard limits SPLN 108:1993. Next on low temperature testing, five samples miniature circuit breakers have change tripping time to be slowed rather than reference temperature testing with deviation MCB A 1.75 until 497.90 second, MCB B 3.81 until 114.89 second, MCB C 2.04 second until 637.42 second, MCB D 0.33 until 1647.96 second, dan MCB E 2.89 until 234.49 second. Last on high temperature testing five samples miniature circuit breakers have change tripping time to be faster rather than reference temperature testing with deviation MCB A 2.63 until 396.93 second, MCB B 2.78 until 251.96 second, MCB C 5.79 second until 775.25 second, MCB D 8.27 until 339.49 second, dan MCB E 3.86 until 95.02 second. Based on this research result, each increase current rate flow through miniature circuit breakers, than miniature circuit breakers tripping time to be faster. When miniature circuit breakers was given low temperature effect, than miniature circuit breakers have change tripping time to be slowed rather than reference temperature. While miniature circuit breakers was given high temperature effect, than miniature circuit breakers have change tripping time to be faster rather than reference temperature. ABSTRAK Tujuan dari penelitian ini adalah untuk mengetahui pengaruh kenaikan besar arus listrik yang disertai dengan perubahan suhu lingkungan terhadap waktu trip pada mini circuit breaker 6A Tipe C. Metode yang digunakan adalah metode eksperimen dengan pendekatan metode kuantitatif. Subjek penelitian yang akan diteliti adalah MCB yang dalam kondisi baru berjumlah 5 sampel produksi asia maupun eropa. Pengumpulan data penelitian dilakukan dengan pengujian menggunakan sumber tegangan PLN, beban linier dan perubahan suhu di chamber pengujian untuk mengetahui karakteristik waktu trip 5 MCB yang mengacu pada SPLN 108:1993. Hasil penelitian menunjukan bahwa, peningkatan besar arus hingga ±2.55 In dan perubahan suhu mempunyai pengaruh terhadap karakteristik waktu trip 5 sampel MCB, dimana pada suhu refrensi masing-masing memiliki perbedaan karakteristik waktu trip namun masih dalam batas standar SPLN 108:1993. Lalu pada pengujian dengan suhu rendah, 5 sampel MCB masing-masing mengalami perubahan waktu trip yang lebih lambat dari pengujian pada suhu refrensi dengan deviasi MCB A 1.75 hingga 497.90 detik, MCB B 3.81 hingga 114.89 detik, MCB C 2.04 detik hingga 637.42 detik, MCB D 0.33 hingga 1647.96 detik, dan MCB E 2.89 hingga 234.49 detik. Sedangkan pada pengujian dengan suhu tinggi 5 sampel MCB masing-masing mengalami perubahan waktu trip yang lebih cepat dari pengujian pada suhu refrensi dengan deviasi MCB A 2.63 hingga 396.93 detik, MCB B 2.78 hingga 251.96 detik, MCB C 5.79 detik hingga 775.25 detik, MCB D 8.27 hingga 339.49 detik, dan MCB E 3.86 hingga 95.02 detik. Dari hasil pengujian yang telah dilakukan di dapatkan hasil semakin besar arus yang melewati MCB maka akan lebih cepat MCB akan trip. Lalu dengan di beri pengaruh suhu rendah, maka MCB akan lebih lambat untuk trip. Sedangkan dengan di beri pengaruh suhu tinggi, maka MCB akan lebih cepat untuk trip.
Indonesia sudah memiliki standar untuk keamanan peralatan rumah tangga yang berbasis kelistrikan yaitu SNI IEC 60335-1:2009. Mesin cuci merupakan salah satu peralatan rumah tangga yang hampir semua kalangan masyarakat memilikinya. Secara umum komponen utama pada mesin cuci adalah motor, oleh karena itu diperlukan pengujian untuk menjamin keamanan motor selama penggunaan. Jenis motor yang umum digunakan untuk peralatan rumah tangga adalah jenis capacitor start motor. Metode resistansi berdasarkan standar SNI/IEC 60335-1:2009 dapat dilakukan kecuali bila lilitannya sejenis atau mendapatkan kesulitan yang berat saat akan melakukan sambungan yang diperlukan. Metode penelitian yang dilakukan adalah dengan melakukan pengukuran perubahan resistansi setiap lilitan dan resistansi lilitan gabungan. Kedua hasil pengukuran tersebut kemudian dianalisa dan dibandingkan dengan standar. Kenaikan temperatur yang terjadi dengan menggunakan metode pertama menghasilkan nilai L1 = 83,33 ºC dan L2 = 66,92 ºC. Sedangkan untuk metode kedua didapat kenaikan temperatur sebesar 66,59 ºC untuk semua belitan. Kenaikan temperatur dengan metode 2 tidak dapat dijadikan acuan untuk penilaian kesesuaian motor mesin cuci karena Δt Ltotal ≠ ΔtL1 + ΔtL2. Oleh karena itu metode yang dapat dipergunakan adalah metode pertama karena mewakili masing-masing lilitan dan nilai yang didapat merupakan nilai yang tidak menguntungkan tetapi masih sesuai dengan batas standar.
Current enhancement without increasing the input power is a critical issue to be pursued for electronic circuits. However, drivability of metal-oxide-semiconductor (MOS) transistors is limited by the source-injection current, and electrons that have passed through the source unavoidably waste their momentum to the phonon bath. Here, we propose the Si electron-aspirator, a nanometer-scaled MOS device with a T-shaped branch, to go beyond this limit. The device utilizes the hydrodynamic nature of electrons due to the electron–electron scattering, by which the injected hot electrons transfer their momentum to cold electrons before they relax with the phonon bath. This momentum transfer induces an electron flow from the grounded side terminal without additional power sources. The operation is demonstrated by observing the output-current enhancement by a factor of about 3 at 8 K, which reveals that the electron–electron scattering can govern the electron transport in nanometer-scaled MOS devices, and increase their effective drivability.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.