This study determined the bond strength of an unfilled resin joined to a feldspathic porcelain for the purpose of evaluating the retentive performance of the prepared material surfaces. Porcelain disks (VMK 68 dentin) were either air abraded with alumina (AAA) or etched with one of the following five etchants: (1) ammonium hydrogen bifluoride (AHB); (2) acidulated phosphate fluoride (APF); (3) hydrofluoric acid (HFA); (4) phosphoric acid (PHA); and (5) sulfuric acid-hydrofluoric acid (SHF). Specimens ground with abrasive paper were also used as controls. After surface preparation, the two different sized porcelain disks were bonded together with a methyl methacrylate-based resin initiated with tri-n-butylborane (MMA-TBB resin). Shear bond strengths were determined both before and after thermocycling. Before the thermocycling, the greatest bond strengths (21.3 and 23.7 MPa) were generated with the use of the SHF and HFA agents, followed by the AHB agent (18.4 MPa). Reduction in bond strength after thermocycling was significant for all groups, although the SHF- and HFA-treated groups exhibited bond strengths greater than 15 MPa even after the thermocycling. The results indicated the effectiveness of the SHF- or HFA-etching for retaining the acrylic resin to the porcelain. However, ageing testing also revealed insufficient retentive characteristics of the acrylic resin by etching alone.

No abstract

This study determined the bond strengths of adhesive resins joined to a feldspathic porcelain (VMK 68) for the purpose of developing the most durable surface preparation for the porcelain. Three porcelain surfaces-ground, air-abraded with alumina, and etched with hydrofluoric acid-were prepared. A two-liquid porcelain conditioner that contained both 4-methacryloyloxyethyl trimellitate anhydride (4-META) and a silane coupler (Porcelain Liner M) was used as the priming agent. Each of the two liquid components of the conditioner was also used individually in order to examine the effects of the respective chemical ingredients on adhesive bonding. Two methyl methacrylate (MMA)-based resins initiated with tri-n-butylborane (TBB) either with or without 4-META (MMA-TBB and 4-META/MMA-TBB resins) were used as the luting agents. Shear bond strengths were determined both before and after thermocycling. Shear testing results indicated that thermocycling was effective for disclosing poor bonding systems, and that both mechanical and chemical retention were indispensable for bonding the porcelain. Of the combinations assessed, etching with hydrofluoric acid followed by two-liquid priming with the Porcelain Liner M material generated the most durable bond strength (33.3 MPa) for the porcelain bonded with the 4-META/MMA-TBB resin (Super-Bond C&B).

No abstract

The aim of this study was to clarify whether marginal grooves on dental implants affect osseointegration, bone structure, and the alignment of collagen fibers to determine bone quality under loaded conditions. Anodized Ti-6Al-4V alloy dental implants, with and without marginal grooves (test and control implants, respectively), were used (3.7 × 8.0 mm). Fourth premolars and first molars of 6 beagle mandibles were extracted. Two control and test implants were placed in randomly selected healed sites at 12 weeks after tooth extraction. Screw-retained single crowns for first molars were fabricated. Euthanasia was performed at 8 weeks after the application of occlusal forces. Implant marginal bone level, bone to implant contact (BIC), bone structure around dental implants, and the alignment of collagen fibers determining bone quality were analyzed. The marginal bone level in test implants was significantly higher than that in control implants. Occlusal forces significantly increased BIC in test implants ( P = .007), whereas BIC did not change in control implants, irrespective of occlusal forces ( P = .303). Moreover, occlusal forces significantly increased BIC in test implants compared with control implants ( P = .032). Additionally, occlusal forces preferentially aligned collagen fibers in test implants, but not control implants. Hence, marginal grooves on dental implants have positive effects on increased osseointegration and adapted bone quality based on the preferential alignment of collagen fibers around dental implants under loaded conditions.