No abstract

B-102Abstrak-Separasi boundary layer merupakan fenomena penting yang mempengaruhi performansi airfoil. Salah satu upaya untuk menunda atau menghilangkan separasi aliran adalah meningkatkan momentum fluida untuk melawan adverse pressure dan tegangan geser permukaan. Hal ini mengakibatkan separasi aliran akan tertunda lebih ke belakang. Upaya tersebut dapat dilakukan dengan penambahan turbulent generator pada upper surface airfoil. Vortex generator (VG) merupakan salah satu jenis turbulent generator yang dapat mempercepat transisi dari laminar boundary layer menjadi turbulent boundary layer. Oleh karena itu, penelitian ini bertujuan untuk mengetahui pengaruh jarak penempatan dan ketinggian VG terhadap perkembangan turbulent boundary layer sehingga dapat meningkatkan performansi airfoil. Penelitian ini dilakukan dengan eksperimen dan numerik pada Re = 1.41x10 5 dengan angle of attack 16°. Benda uji yang digunakan adalah airfoil NASA LS-0417 dengan dan tanpa VG. Variasi jarak penempatan dan ketinggian VG yaitu x/c = 0.1; 0.2; 0.3; 0.4 (h) = 1 mm; 3 mm; 5 mm. Hasil yang didapatkan adalah variasi vortex generator paling optimal adalah vortex generator dengan x/c = 0.3 dan h = 1 mm dimana Nilai CL/CD mengalami kenaikan sebesar 14.337%.

The periodic changes of the angles of attack in time occurring in the Darrieus turbine blade result in the significant increase of unsteady characteristics, commonly referred as dynamic stall. CFD simulations using SST k-ω turbulence model with Kato-Launder correction were used to examine the physical phenomena occurring on the sectional airfoil of the blade. The blade was modeled as an airfoil rotating about its center of rotation. The CFD calculations show remarkable differences of the forces acting on the airfoil compared with the static condition due to the traveling vortices phenomena. The generation of leading edge and trailing edge vortices as the characteristics of dynamic stall was captured accurately. This provided more detailed information on the development of dynamic stall on the Darrieus turbine blade. The analysis of the stall event was obtained by considering the insertion flow occurring near the leading edge. The interactions of the travelling vortices in the upwind as well as in the downwind phases are presented in the present manuscript, providing deeper knowledge in the dynamic stall database of vertical axis wind turbines.

The necessity in the analysis of dynamic stall becomes increasingly important due to its impact on many streamlined structures such as helicopter and wind turbine rotor blades. The present paper provides Computational Fluid Dynamics (CFD) predictions of a pitching NACA 0012 airfoil at reduced frequency of 0.1 and at small Reynolds number value of 1.35e5. The simulations were carried out by adjusting the k − ε URANS turbulence model in order to damp the turbulence production in the near wall region. The damping factor was introduced as a function of wall distance in the buffer zone region. Parametric studies on the involving variables were conducted and the effect on the prediction capability was shown. The results were compared with available experimental data and CFD simulations using some selected two-equation turbulence models. An improvement of the lift coefficient prediction was shown even though the results still roughly mimic the experimental data. The flow development under the dynamic stall onset was investigated with regards to the effect of the leading and trailing edge vortices. Furthermore, the characteristics of the flow at several chords length downstream the airfoil were evaluated.

The research is conducted in order to reduce energy losses caused by the secondary flow in the endwall junction. This phenomenon is caused by the interaction of two adjacent viscous flow (symmetric airfoil and endwall). Reduction of energy loss carried out by addition of Foward Facing Step Turbulator (FFST) in the upstream. Endwall junction area is modeled as a NACA 0015 airfoil and a flat plate. Position of FFST is at a distance L = 2/3 C upstream leading edge and a thickness d = 4% C. Free stream conditions Red = 105 with turbulence intensity (Tu) 5%. Research is conducted by numerical and experiment methods. Pathlines of numerical result methods has an identic structure with "Oil Flow Visualization" of the experiment.Result of the research states that the addition of FFST can increase the turbulence intensity in the flow near the wall. So at the same angle of attact (α), the saddle point position on the leading edge has distance nearly the same but a little more towards the lower side and the separation line is wider than without FFST. Because the flow has stronger turbulence intensity, attachment line of the upper and lower sides have a better capability of following the contours of the body. So the point of separation can be delayed and blockage (energy loss) can be reduced as well. Reduction of energy loss is most effective on α=8 ° (4.16%),Keyword : Secondary flow, forward facing step, turbulent intensity.