Due to their high specific surface area and advanced properties, TiO2 nanotubes (TiO2 NTs) have a great significance for production and storage of energy. In this paper, TiO2 NTs were synthesized from anodization of Ti-6Al-4V alloy at 60 V for 3 h in fluoride ethylene glycol electrolyte by varying the water content and further annealing treatment. The morphological, structural, optical and electrochemical performances of TiO2 NTs were investigated by scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), UV-Visible spectroscopy and electrochemical characterization techniques. By varying the water content in the solution, a honeycomb and porous structure was obtained at low water content and the presence of (α + β) phase in Ti-6Al-4V alloy caused not uniform etching. With an additional increase in water content, a nanotubular structure is formed in the (α + β) phases with different morphological parameters. The anatase TiO2 NTs synthesized with 20 wt% H2O shows an improvement in absorption band that extends into the visible region due the presence of vanadium oxide in the structure and the effective band gap energy (Eg) value of 2.25 eV. The TiO2 NTs electrode also shows a good cycling performance, delivering a reversible capacity of 82 mAh.g−1 (34 μAh.cm−2.μm−1) at 1C rate over 50 cycles.
Background: A nano-tubular structure of Titanium dioxide (TiO2) was obtained using an electrochemical process based on the anodization of titanium foil in an organic electrolyte prepared with ethylene glycol (HOCH2CH2OH) containing Ammonium fluorides (NH4F) and ultrapure water under different anodization voltage. The morphological characteristics showed the formation of TiO2 nanotubes with different geometrical parameters. The electronic properties of the TiO2 NTs films were measured by the Mott-Schottky (MS) plots, indicating a positive slope for all graphs implying the n-type semiconductor nature of the TiO2 nanotubes (TiO2 NTs). The donor density (Nd) and the flat band potential (Efb) increases slightly with increase the anodization voltage. Methods: Prior the anodization, the titanium (Ti) foils were cut into square shape (2.25 cm2) with a selected work area of 0.6 cm2. The samples were subjected to a final polishing using a rotating felt pad (01 &µm) impregnated with alumina until a metallic mirror surface was obtained. The Ti foils were degreased by sonication in acetone, methanol and 2-Propanol for 10 minutes respectively, rinsed with ultrapure water and dried in a stream of compressed air. To form a TiO2 NTs, electrochemical anodization process was carried out at room temperature in Ethylene Glycol (EG) solution containing 0.3 wt% Ammonium fluorides (NH4F) and 2wt % ultrapure water for three (03) hours at different anodization voltage (20, 40 and 60V). A two-electrode cell was used for all the anodization measurements, with a platinum plate as the counter electrode, separated from the working electrode (titanium foil) by 1.5 cm. Immediately after anodization, the samples were soaked in ultrapure water to remove residual electrolyte for 10 minutes and then dried in an oven at 50 °C for 10 minutes. Results: TiO2 NTs grown from anodization of Ti foil in fluoride EG solution for 3h by varying the anodization voltage. The micrographic analysis shows a strong influence of the anodizing voltage on the morphology and geometrical parameters of the TiO2 NTs. Non homogenous NTs morphology was observed at 20 V with the presence of corrugations along the walls of the tubes. A perfect and regular nanotublar structure with smooth’s walls tubes was obtained at an anodization voltage of 60V. Moreover, the increase of anodization voltage leads to an increase in both the diameter and the length of tubes. In fact, the inner diameter and the length of the tubes (Di and L) values increase with increasing potential, being around (39 nm and 2 &µm) respectively at 20 V and (106 nm and 16,1 &µm) at 60 V. The measured electronic properties of TiO2 NTs indicating the n type semiconducting nature. It is remarkable that the donor density Nd increases toward higher values by increasing the anodizing voltage until 40V. However, for an anodization at 60V, the Nd has a small decrease value (7, 03 * 1019 cm-3) indicating a diminution of defects present in the material. Also, by increasing the anodizing voltage, Efb takes increasingly more positive values. In fact, the Efb values are – 0.12, 0.05 and 0.15 V for films prepared at 20, 40 and 60 V respectively. Therefore, this behavior can be attributed to a displacement of the Fermi level toward the conduction band edge which leads to a larger band bending at the interface. Conclusion: By varying the anodization voltage, titanium dioxide nanotubes (TiO2 NTs) were grown using electrochemical anodization of titanium foil in fluoride ethylene glycol solution for 3 hours. The morphology of the TiO2 NTs obtained was considerably affected; the anodizing potential determines the migration of ions in electrolyte during anodization process and simultaneously the tube diameter. An average small a nanotube diameter around 39 nm was obtained for 20V corresponding to 106 nm average diameter for TiO2 NTs structure synthesized at 60V. Furthermore, the semiconductor properties of the TiO2 NTs films have also been modified with increased values while increasing the anodization voltage. This behavior was attributed that the TiO2 NTs structure is more disordered, having much more defects provide abundant local donor energy levels which increases conductivity and decrease the probability of recombination of electrons and holes in these films, that can be integrated as active layer in the solar cells, in particular the Gratzel cells.
Governments have imposed social distancing regulations to counter the coronavirus pandemic. An automated occupancy control system to provide a more cost-effective and efficient way to abide with these safety regulations. With the generalization of the use of digital images, the analysis of movement in video sequences has proved to be an essential tool for various applications such as video surveillance, robotics etc. The advance in video processing algorithms and the fast computational capability, give a possibility to use a video tracking and counting people in real time. Estimating the number of people in real time is useful information for several applications such as security and health management. With the COVID-19 pandemic, the counting of people present in a region of interest is important to control the area occupancy in order to minimize human virus transmission. In this paper we present a finished solution for counting people present in the same area. The system is based on Raspberry Pi and a common camera. The method called BLOB (Binary Large Object) analysis is used. The performance of the system, achieving an average count rate between 95% and 98%.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.