Among 3D-printed composite scaffolds for bone tissue engineering, researchers have been attracted to the use of zinc ions to improve the scaffold’s anti-bacterial activity and prevent surgical site infection. In this study, we assumed that the concentration of zinc ions released from the scaffold will be correlated with the thickness of the zinc oxide coating on 3D-printed scaffolds. We investigated the adequate thickness of zinc oxide coating by comparing different scaffolds’ characteristics, antibacterial activity, and in vitro cell response. The scaffolds’ compressive modulus decreased as the zinc oxide coating thickness increased (10, 100 and 200 nm). However, the compressive modulus of scaffolds in this study were superior to those of other reported scaffolds because our scaffolds had a kagome structure and were made of composite material. In regard to the antibacterial activity and in vitro cell response, the in vitro cell proliferation on scaffolds with a zinc oxide coating was higher than that of the control scaffold. Moreover, the antibacterial activity of scaffolds with 100 or 200 nm-thick zinc oxide coating on Escherichia coli was superior to that of other scaffolds. Therefore, we concluded that the scaffold with a 100 nm-thick zinc oxide coating was the most appropriate scaffold to use as a bone-regenerating scaffold, given its mechanical property, its antibacterial activity, and its in vitro cell proliferation.
In the use of the medical devices, it is essential to prevent the attachment of bacteria to the device surface or to kill the attached bacteria. To kill bacteria, many researchers have used antibiotics or studied nanostructure-based antibacterial surfaces, which rely on mechanical antibacterial methods. Several polymers are widely used for device fabrication, one of which is polycaprolactone (PCL). PCL is biocompatible, biodegradable, easy to fabricate using 3D printing, relatively inexpensive and its quality is easily controlled; therefore, there are various approaches to its use in bio-applications. In addition, it is an FDA-approved material, so it is often used as an implantable material in the human body. However, PCL has no inherent antibacterial function, so it is necessary to develop antibacterial functions in scaffold or film-based PCL medical devices. In this study, process parameters for nanopillar fabrication were established through a simple thermal imprinting method with PCL. Finally, a PCL film with a flexible and transparent nanopillar structure was produced, and the mechano-bactericidal potential was demonstrated using only one PCL material. PCL with nanopillars showed bactericidal ability against Escherichia coli (E. coli) and Bacillus subtilis (B. subtilis) bacteria cultured on its surface that resulted in membrane damage and death due to contact with nanopillars. Additionally, bacteriostatic results were shown to inhibit bacterial growth and activity of Staphylococcus aureus (S. aureus) on PCL nanostructured columns. The fabricated nanopillar structure has confirmed that mechanically induced antibacterial function and can be applied to implantable medical devices.
Antibacterial surfaces are one of the most important surfaces in the medical and marine industries. Many researchers are studying antibacterial surfaces to kill bacteria or prevent adhesions. Various materials and structures are applied to the surface to inhibit the adhesion of bacteria or kill the adhered bacteria. Nowadays, a dual strategy is preferred rather than a single strategy. In this study, nanopillar structures were fabricated using polyethylene glycol dimethacrylate (PEGDMA), which has an antifouling effect. Afterward, the fabricated nanostructured PEGDMA was assessed to confirm the intrinsic antibacterial effect and mechanically induced antibacterial functions. The adhesion of Gram-negative and Grampositive bacteria can be effectively reduced by the PEG hydration layer formation, steric repulsion, and flexible chain, and the nanostructure can damage the bacterial membrane. In addition, we performed antibacterial experiments on a nanopillar-structured surface made of PEGDMA. Furthermore, we revealed that the mechanical robustness of the nanopillared surface was superior to that of the nanocone-structured surface using computational analysis. Nanopillar structures fabricated using PEGDMA are promising candidates for antifouling and antibacterial surfaces and can be applied in various industries.
Abstract. The purpose of this study was to investigate the effects of shift work on depression. Data from the study were analyzed using the The sixth Korea National Health and Nutrition examination survey Ⅵ-2. The results showed that the shift worker had 1.459 times more depressed than the non-shift worker. The quality of life and perception of subjective health status of shift workers were found to be related to depression. The quality of life of these shift workers and the policy approach to improve industrial safety are considered to be a way to improve the mental health of shift workers.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.