No abstract

Production rate is an increasingly important factor in the deployment of metal additive manufacturing (AM) throughout industry. To address the perceived low production rate of metal AM systems based on single-laser powder bed fusion (L-PBF), several companies now offer systems in which melting has been parallelised by the introduction of multiple, independently controlled laser beams. Nevertheless, a full set of studies is yet to be conducted to benchmark the efficiency of multi-laser systems and, at the same time, to verify if the mechanical properties of components are compromised due to the increase in build rate. This study addresses the described technology gaps and presents a 4-beam L-PBF system operating in "single multi" (SM) mode (SM-L-PBF) where each of the four lasers is controlled so that it melts all of a particular components' layers and produces specimens for comparison with standard L-PBF specimens from the same machine. That is all four lasers making all of some of the parts were compared to a single-laser manufacturing all of the parts. Build parameters were kept constant throughout the manufacturing process and the material used was Inconel 625 (IN625). Stress-relieving heat treatment was conducted on As-built (AB) specimens. Both AB and heat-treated (HT) specimen sets were tested for density, microstructure, tensile strength and hardness. Results indicate that the stress-relieving heat treatment increases specimen ductility without compromising other mechanical properties. SM-L-PBF has achieved a build rate of 14 cm 3 /h when four 200 W lasers were used to process IN625 at a layer thickness of 30 μm. An increase in the build rate of 2.74 times (build time reduction: 63%) has been demonstrated when compared to that of L-PBF, with little to no compromises in specimen mechanical properties. The observed tensile properties exceed the American Society for Testing Materials (ASTM) requirements for IN625 (by a margin of 22 to 26% in the 0.2% offset yield strength). Average specimen hardness and grain size are in the same order as that reported in literatures. The study has demonstrated that a multi-laser AM system opens up opportunities to tackle the impasse of low build rate in L-PBF in an industrial setting and that at least when operating in single mode there is no detectable degradation in the mechanical and crystallographic characteristics of the components produced.

Electron beam additive manufacturing (EBAM) is an additive manufacturing (AM) technique increasingly used by many industrial sectors, including medical and aerospace industries. The application of this technology is still, however, challenged by many technical barriers. One of the major issues is the lack of process monitoring and control system to monitor process repeatability and component quality reproducibility. Various techniques, mainly involving infrared (IR) and optical cameras, have been employed in previous attempts to study the quality of the EBAM process. However, all attempts lack the flexibility to zoom-in and focus on multiple regions of the processing area. In this paper, a digital electronic imaging system prototype and a piece of macroscopic process quality analysis software are presented. The prototype aims to provide flexibility in magnifications and the selection of fields of view (FOV). The software aims to monitor the EBAM process on a layer-by-layer basis. Digital electronic images were generated by detecting both secondary electrons (SE) and backscattered electrons (BSE) originating from interactions between the machine electron beam and the processing area using specially designed hardware. Prototype capability experiments, software verification and demonstration were conducted at room temperature on the top layer of an EBAM test build. Digital images of different magnifications and FOVs were generated. The upper range of the magnification achieved in the experiments was 95 and the demonstration verified the potential ability of the software to be applied in process monitoring. It is believed that the prototype and software have significant potential to be used for in-process EBAM monitoring in many manufacturing sectors. This study is thought to be the necessary precursor for future work which will establish whether the concept is suited to working under in-process EBAM operating conditions.

Purpose Electron beam additive manufacturing (EBAM) is a popular additive manufacturing (AM) technique used by many industrial sectors. In EBAM process monitoring, data analysis is focused on information extraction directly from the raw data collected in-process, i.e. thermal/optical/electronic images, and the comparison between the collected data and the computed tomography/microscopy images generated after the EBAM process. This paper aims to postulate that a stack of bitmaps could be generated from the computer-aided design (CAD) at a range of Z heights and user-defined region of interest during file preparation of the EBAM process, and serve as a reference image set. Design/methodology/approach Comparison between that and the workpiece images collected during the EBAM process could then be used for quality assessment purposes. In spite of the extensive literature on CAD slicing and contour generation for AM process preparation, the method of bitmap generation from the CAD model at different field of views (FOVs) has not been disseminated in detail. This article presents a piece of custom CAD-bitmap generation software and an experiment demonstrating the application of the software alongside an electronic imaging system prototype. Findings Results show that the software is capable of generating binary bitmaps with user-defined Z heights, image dimensions and image FOVs from the CAD model; and can generate reference bitmaps to work with workpiece electronic images for potential pixel-to-pixel image comparison. Originality/value It is envisaged that this CAD-bitmap image generation ability opens up new opportunities in quality assessment for the in-process monitoring of the EBAM process.

No abstract

No abstract

No abstract

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.