This study aimed to investigate the effect of surface treatment and type of composite resin material on the color stability and surface roughness of different denture characterizing composites. Materials and methods: Two nanohybrids [Gradia Plus Gum, (GP) and SR Nexco Paste Gingiva, (SR)] and one microhybrid gingiva-colored composite resin [Amaris Gingiva, (AG)] were investigated. A total of 120 disk-shaped samples were prepared, 40 of each material. Samples were divided into two groups (n = 20) for each material according to the surface treatment applied: conventional polishing (control) and coated with a sealant in addition to the surface polishing. All groups were thermocycled. The surface roughness (Ra) was measured using a profilometer after thermal cycling. The samples were then divided into 2 subgroups (n = 10) and stored for 7 days in distilled water or coffee solution. Color differences (ΔE 00 ) were calculated with a spectrophotometer. Results were evaluated with Kruskal-Wallis and Mann-Whitney U statistical analysis. Results:The type of denture characterizing composite material and surface treatment method revealed statistically significant differences for the ΔE 00 (after immersion both in coffee and distilled water) and the Ra values of denture characterizing composite (p < 0.001 for both). All sealed groups showed significantly higher Ra than the all polished groups. Both in the polished groups and the sealant applied groups, the GP had the highest mean Ra values (0.29 ±0.05 µm and 0.47 ±0.09 µm, respectively). It was followed by SR (0.23 ±0.06 µm and 0.41 ±0.10 µm, respectively), and AG groups (0.20 ±0.06 µm and 0.39 ±0.09 µm, respectively). According to the mean ΔE 00 results, all composite groups showed significantly higher ΔE 00 values immersed in coffee solutions compared to distilled water. In coffee solutions, the highest ΔE 00 was observed in the polished GP (1.90 ±0.40), and the lowest ΔE 00 was observed in the polished SR (0.97 ±0.36). The sealed groups showed higher ΔE 00 than the polished groups, except for GP. Conclusions: The surface roughness value of sealant applied groups were significantly higher than those of the polished groups. The surface sealant application significantly increased the staining of all composite groups compared to conventional polishing, except for GP.
Amaç: Çalışmanın amacı; farklı protez temizleme ajanlarının, total protezlerin diş eti modifikasyonunda kullanılan indirekt kompozit rezinler ve ısı ile polimerize olan akrilik kaide materyalinin yüzey pürüzlülüğüne etkisini değerlendirmektir. Gereç ve Yöntemler: Çalışmada iki farklı indirekt diş eti kompoziti (Gradia Plus Gum ve SR Nexco Paste Gingiva) ve bir adet ısı ile polimerize olan polimetil metakrilat akrilik rezin (PMMA) (Meliodent) test edildi. Her materyalden 30 adet olmak üzere çapı 10 mm, yüksekliği 2 mm olan disk şeklinde toplam 90 adet örnek hazırlandı. Örnekler temizleme solüsyonlarına göre 3 alt gruba ayrılarak (n = 10) distile su (kontrol) ve iki farklı protez temizleme solüsyonunda (% 1’lik NaOCl ve Corega) 90 günlük kullanım süresine eşit olacak şekilde bekletildi. Örneklerin başlangıç (Ra0) ve 90 gün sonra (Ra1) yüzey pürüzlülüğü ölçümleri profilometre ile yapıldı. Elde edilen veriler Kruskal-Wallis ve Mann-Whitney U testleri kullanılarak analiz edildi. Wilcoxon Signed Rank testi her materyalin Ra0 ve Ra1 değerlerini kıyaslamada kullanıldı (p < 0.05). Bulgular: Farklı protez temizleme solüsyonlarının, materyallerin yüzey pürüzlülük değerlerine etkisi istatistiksel olarak anlamlıydı (p < 0.001). Tüm materyaller için, Ra0 ve Ra1 değerleri arasındaki farklılık % 1’lik NaOCl’de istatistiksel olarak anlamlı iken (p < 0.05) Corega için istatistiksel bir fark gözlenmedi. % 1’lik NaOCl PMMA’nın yüzey pürüzlülüğünde istatistiksel olarak anlamlı azalmaya sebep olurken, kompozit materyallerinde artışa sebep olmuştur. Sonuç: % 1’lik NaOCl protez temizleme solüsyonu, PMMA akrilik rezinlerin kimyasal temizliği için önerilebilir ancak kompozit rezinlerle modifiye edilen total protezlerde yüzey pürüzlülüğünü arttırdığı dikkate alınmalıdır. Alkalen peroksit içerikli Corega efervesan tabletin ise test edilen tüm materyaller için uygun bir temizleme solüsyonu olduğu söylenebilir.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.