No abstract

Both lasers promote morphologic changes and debris removal. These alterations of the dentin surface appeared to be more evident in the Nd:YAG laser group, but the diode laser group showed more uniform changes.

We concluded that the combination of the Nd:YAG laser and AH Plus showed the best results.

The purpose of this study was to compare, in vitro, by means of computerized analysis of digital radiographic images, the anatomic alterations produced in the mandibular molar tooth dentinal walls of mesiobucal canals with severe curvature by three different endodontic techniques: Progressive Preparation, Staged and Serial Preparation. A selection was made of 45 extracted, human, mandibular molars, with root curvatures greater than 25 degrees. They were divided into three groups for every technique studied, which were then sub-divided into three sub-groups in accordance with the position of the curvature along the root: cervical, median or apical. After access surgery and tooth length determination, the canals were filled with 100% Barium Sulphate radiological contrast and the teeth were then radiographed with a direct digital radiography system, using a special apparatus capable of keeping the samples in the same spatial position during the different radiographic takes. After the above-mentioned endodontic techniques had been performed, the teeth were again filled with Barium sulphate and were also radiographed under the same previously mentioned conditions. The pre- and post-operative digital images were then analyzed in two computerized programs, AutoCAD 2004 and CorelDraw 10, to assess, respectively, the areas and the horizontal alterations which occurred in the internal and external walls of the root canals. The results indicated that although no significant differences among the techniques were shown in the statistical analysis, in a descriptive analysis the Progressive Preparation technique was shown to be more regular, uniform and effective.

The aim of this study was to assess the correlation between the degree of angulation and the position of root curvatures and their influence on the comparative results between the performances of the Progressive, Staged and Serial Preparation Techniques. The mesiobucal canals of 70 extracted mandibular molars were filled with a radiological contrast of 100% Barium sulphate and radiographed with a direct digital radiographic system, in an apparatus that guarantees that the samples remain in the same spatial position at all times. The images were then analyzed in the Coreldraw 10 program (MicroSafe, RJ, Brasil) in accordance with two criteria: the methods of Berbert, Nishiyama(1) (1994) and Schneider11 (1971) to determine the position and the angle of the root curvatures, respectively. Initially, the possibility of correlation between these two variables was studied. The teeth were then selected according to angulation (greater than 25 degrees) and position of root curvatures (cervical, median and apical) in order to perform the endodontic techniques. After preparation, the samples were radiographed again and the images were superimposed in order to compare the pre- and post-operative areas. The difference between them showed the percentage of widening for each technique. The results showed that there was no correlation between the angulations and the root curvature positions, and that the different positions did not interfere in the performance of the techniques. The Progressive Preparation technique produced the highest widening values for all the groups, irrespective of the root curvature position.

The 810-nm-diode laser irradiation did not promote significant differences in apical leakage.

Objective: The goal of this study was to evaluate the infection control measures actually implemented by dental surgeons during dental practice, as patients and professionals are exposed to high biological risk in dental care environments. Method: 614 questionnaires (90.69%) were answered by professionals registered in updating or in post-graduate courses in the Municipality of São Paulo. Results: Out of surveyed professionals 30.62% admitted that surface protection barriers were not used, whereas 34.17% were using non ideal or outdated pre-disinfection practices. The autoclave was used by 69.38% of participants, although 33.80% were not monitoring control of the sterilization cycles. Chemical and biological indicators were not used simultaneously by 83.21% of respondents and were not employed on a daily or weekly basis by at least 81.75%. Dubious methods of sterilization were cited by 44.77%. Occupational accidents caused by cutting and piercing objects were reported by 47.88%; however, the biologic risk was underestimated by 74.15% of the professionals who suffered the accidents. Irritant solutions were used as an antiseptic agent by 18.55%. Conclusions: Infection control measures reported by dental surgeons during their practices are defi cient. It is necessary to educate, raise awareness of professionals, and promote constant updating courses on procedures which aim at improving safety of dental care.

The aim of this study was to comparatively evaluate the bending resistance at 45º, the static and dynamic cyclic fatigue life, and the fracture type of the WaveOne (Dentsply Maillefer, Ballaigues, Switzerland) 25-08 and Reciproc (VDW, Munich, Germany) 25-08 instruments. A total of 60 nickel-titanium (NiTi) instruments (30 Reciproc and 30 WaveOne) from three different lots, each of which was 25 mm in length, were tested. The bending resistance was evaluated through the results of a cantilever-bending test conducted using a universal testing machine. Static and dynamic cyclic fatigue testing was conducted using a custom-made device. For the static and dynamic tests, a cast Ni-Cr-Mo-Ti alloy metal block with an artificial canal measuring 1.77 mm in diameter and 20.00 mm in total length was used. A scanning electron microscope was used to determine the type of fracture. Statistical analyses were performed on the results. The WaveOne instrument was less flexible than the Reciproc (p < 0.05). The Reciproc instrument showed better resistance in the static and dynamic cyclic fatigue tests (p < 0.05). The transverse cross-section and geometry of the instruments were important factors in their resistance to bending and cyclic fracture. Both of the instruments showed ductile-type fracture characteristics. It can be concluded that the Reciproc 25-08 instrument was more resistant to static and dynamic cyclic fatigue than the WaveOne 25-08 instrument, while the WaveOne 25-08 instrument was less flexible. Bending and resistance to cyclic fracture were influenced by the instruments' geometries and transverse cross-sections. Both of the instruments showed ductile-type fracture characteristics.