No abstract

Coating is an essential step in adjusting the surface properties of materials. Superhydrophobic coatings with contact angles greater than 150° and roll-off angles below 10° for water have been developed, based on low-energy surfaces and roughness on the nano- and micrometer scales. However, these surfaces are still wetted by organic liquids such as surfactant-based solutions, alcohols, or alkanes. Coatings that are simultaneously superhydrophobic and superoleophobic are rare. We designed an easily fabricated, transparent, and oil-rebounding superamphiphobic coating. A porous deposit of candle soot was coated with a 25-nanometer-thick silica shell. The black coating became transparent after calcination at 600°C. After silanization, the coating was superamphiphobic and remained so even after its top layer was damaged by sand impingement.

Thermal fluctuations of the cantilever are a fundamental source of noise in atomic force microscopy. We calculated thermal noise using the equipartition theorem and considering all possible vibration modes of the cantilever. The measurable amplitude of thermal noise depends on the temperature, the spring constant K of the cantilever and on t h e method by which the cantilever deflection is detected. If the deflection is measured directly, e.g. with an interferometer or a scanning tunneling microscope, the thermal noise of a cantilever with a free end can be calculated from m. If the end of the cantilever is supported by a hard surface no thermal fluctuations of the deflection are possible. If the optical lever technique is applied to measure the deflection, the thermal noise of a cantilever with a free end is d m . When the cantilever is supported thermal noise decreases to w , but it does not vanish.

For several centuries fluid dynamics studies have relied upon the assumption that when a liquid flows over a solid surface, the liquid molecules adjacent to the solid are stationary relative to the solid. This no-slip boundary condition (BC) has been applied successfully to model many macroscopic experiments, but has no microscopic justification. In recent years there has been an increased interest in determining the appropriate BCs for the flow of Newtonian liquids in confined geometries, partly due to exciting developments in the fields of microfluidic and microelectromechanical devices and partly because new and more sophisticated measurement techniques are now available. An increasing number of research groups now dedicate great attention to the study of the flow of liquids at solid interfaces, and as a result a large number of experimental, computational and theoretical studies have appeared in the literature. We provide here a review of experimental studies regarding the phenomenon of slip of Newtonian liquids at solid interfaces. We dedicate particular attention to the effects that factors such as surface roughness, wettability and the presence of gaseous layers might have on the measured interfacial slip. We also discuss how future studies might improve our understanding of hydrodynamic BCs and enable us to actively control liquid slip.

In atomic force microscopy, the tip experiences electrostatic, van der Waals, and hydration forces when imaging in electrolyte solution above a charged surface. To study the electrostatic interaction force vs distance, curves were recorded at different salt concentrations and pH values. This was done with tips bearing surface charges of different sign and magnitude (silicon nitride, Al(2)O(3), glass, and diamond) on negatively charged surfaces (mica and glass). In addition to the van der Waals attraction, neutral and negatively charged tips experienced a repulsive force. This repulsive force depended on the salt concentration. It decayed exponentially with distance having a decay length similar to the Debye length. Typical forces were about 0.1 nN strong. With positively charged tips, purely attractive forces were observed. Comparing these results with calculations showed the electrostatic origin of this force.In the presence of high concentrations (> 3 M) of divalent cations, where the electrostatic force can be completely ignored, another repulsive force was observed with silicon nitride tips on mica. This force decayed roughly exponentially with a decay length of 3 nm and was approximately 0.07-nN strong. This repulsion is attributed to the hydration force.

No abstract

The development of polymers with switchable glass transition temperatures (T) can address scientific challenges such as the healing of cracks in high-T polymers and the processing of hard polymers at room temperature without using plasticizing solvents. Here, we demonstrate that light can switch the T of azobenzene-containing polymers (azopolymers) and induce reversible solid-to-liquid transitions of the polymers. The azobenzene groups in the polymers exhibit reversible cis-trans photoisomerization abilities. Trans azopolymers are solids with T above room temperature, whereas cis azopolymers are liquids with T below room temperature. Because of the photoinduced solid-to-liquid transitions of these polymers, light can reduce the surface roughness of azopolymer films by almost 600%, repeatedly heal cracks in azopolymers, and control the adhesion of azopolymers for transfer printing. The photoswitching of T provides a new strategy for designing healable polymers with high T and allows for control over the mechanical properties of polymers with high spatiotemporal resolution.

No abstract