The effect of controlled thermal annealing on charge transport and photogeneration in bulk‐heterojunction solar cells made from blend films of regioregular poly(3‐hexylthiophene) (P3HT) and methanofullerene (PCBM) has been studied. With respect to the charge transport, it is demonstrated that the electron mobility dominates the transport of the cell, varying from 10–8 m2 V–1 s–1 in as‐cast devices to ≈3 × 10–7 m2 V–1 s–1 after thermal annealing. The hole mobility in the P3HT phase of the blend is dramatically affected by thermal annealing. It increases by more than three orders of magnitude, to reach a value of up to ≈ 2 × 10–8 m2 V–1 s–1 after the annealing process, as a result of an improved crystallinity of the film. Moreover, upon annealing the absorption spectrum of P3HT:PCBM blends undergo a strong red‐shift, improving the spectral overlap with solar emission, which results in an increase of more than 60 % in the rate of charge‐carrier generation. Subsequently, the experimental electron and hole mobilities are used to study the photocurrent generation in P3HT:PCBM devices as a function of annealing temperature. The results indicate that the most important factor leading to a strong enhancement of the efficiency, compared with non‐annealed devices, is the increase of the hole mobility in the P3HT phase of the blend. Furthermore, numerical simulations indicate that under short‐circuit conditions the dissociation efficiency of bound electron–hole pairs at the donor/acceptor interface is close to 90 %, which explains the large quantum efficiencies measured in P3HT:PCBM blends.

In organic field-effect transistors (FETs), charges move near the surface of an organic semiconductor, at the interface with a dielectric. In the past, the nature of the microscopic motion of charge carriers--which determines the device performance--has been related to the quality of the organic semiconductor. Recently, it was discovered that the nearby dielectric also has an unexpectedly strong influence. The mechanisms responsible for this influence are not understood. To investigate these mechanisms, we have studied transport through organic single-crystal FETs with different gate insulators. We find that the temperature dependence of the mobility evolves from metallic-like to insulating-like with increasing dielectric constant of the insulator. The phenomenon is accounted for by a two-dimensional Fröhlich polaron model that quantitatively describes our observations and shows that increasing the dielectric polarizability results in a crossover from the weak to the strong polaronic coupling regime. This represents a considerable step forward in our understanding of transport through organic transistors, and identifies a microscopic physical process with a large influence on device performance.

The electronic properties of interfaces between two different solids can differ strikingly from those of the constituent materials. For instance, metallic conductivity-and even superconductivity-have recently been discovered at interfaces formed by insulating transition-metal oxides. Here, we investigate interfaces between crystals of conjugated organic molecules, which are large-gap undoped semiconductors, that is, essentially insulators. We find that highly conducting interfaces can be realized with resistivity ranging from 1 to 30 kohms per square, and that, for the best samples, the temperature dependence of the conductivity is metallic. The observed electrical conduction originates from a large transfer of charge between the two crystals that takes place at the interface, on a molecular scale. As the interface assembly process is simple and can be applied to crystals of virtually any conjugated molecule, the conducting interfaces described here represent the first examples of a new class of electronic systems.

The origin of the enhanced performance of bulk heterojunction solar cells based on slowly dried films of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl C61-butyric acid methyl ester is investigated, combining charge transport measurements with numerical device simulations. Slow drying leads to a 33-fold enhancement of the hole mobility up to 5.0×10−7m2V−1s−1 in the P3HT phase of the blend, thereby balancing the transport of electrons and holes in the blend. The resulting reduction of space-charge accumulation enables the use of thick films (∼300nm), absorbing most of the incoming photons, without losses in the fill factor and short-circuit current of the device.

No abstract