inorganic photovoltaic cells based on crystal-silicon, the solution processability of OPV cells makes it suitable for the largescale solution production at room temperature via the roll-to-roll method, which promises low-cost and large area device fabrication onto flexible substrates. [4][5][6] Benefiting from the great efforts devoted to the design of new materials, [7][8][9][10][11][12][13] optimization of the blend morphology, [14][15][16][17][18] understanding the charge generation mechanism, [19][20][21][22][23][24][25][26] significant progress has been achieved in the last few years. Recently, the power conversion efficiencies (PCEs) of OPV cells have surpassed ≈15%. [27][28][29] However, the devices with cutting-edge performance are fabricated using highly toxic solvents like chlorinated and/or aromatic solvents, which is not adaptable for large-scale production and becoming a severe problem that hinders the mass production of the OPV cells. Therefore, the material design of OPV materials should take both the efficiency and processability into consideration.At present, the commonly used processing solvents for high-performance OPV materials are chlorobenzene (CB) and chloroform (CF), as they possess excellent dissolving capability of the highly conjugated structures. [30][31][32] Over the last few years, the design and application of nonfullerene acceptors (NFAs) have achieved Recent advances in nonfullerene acceptors (NFAs) have enabled the rapid increase in power conversion efficiencies (PCEs) of organic photovoltaic (OPV) cells. However, this progress is achieved using highly toxic solvents, which are not suitable for the scalable large-area processing method, becoming one of the biggest factors hindering the mass production and commercial applications of OPVs. Therefore, it is of great importance to get good eco-compatible processability when designing efficient OPV materials. Here, to achieve high efficiency and good processability of the NFAs in eco-compatible solvents, the flexible alkyl chains of the highly efficient NFA BTP-4F-8 (also known as Y6) are modified and BTP-4F-12 is synthesized. Combining with the polymer donor PBDB-TF, BTP-4F-12 shows the best PCE of 16.4%. Importantly, when the polymer donor PBDB-TF is replaced by T1 with better solubility, various eco-compatible solvents can be applied to fabricate OPV cells. Finally, over 14% efficiency is obtained with tetrahydrofuran (THF) as the processing solvent for 1.07 cm 2 OPV cells by the blade-coating method. These results indicate that the simple modification of the side chain can be used to tune the processability of active layer materials and thus make it more applicable for the mass production with environmentally benign solvents. Organic PhotovoltaicsOrganic photovoltaic (OPV) cells consisting of organic layers as photoactive materials are one of the most promising next-generation photovoltaic technologies to harvest clean and renewable solar energy. [1][2][3] When compared with the conventional
A series of organic- and water-soluble distyrylbenzene-based two-photon absorption (TPA) fluorophores containing dialkylamino donor groups at the termini was designed, synthesized, and characterized. The central core was systematically substituted to modulate intramolecular charge transfer (ICT). These molecules allow an examination of solvent effects on the TPA cross section (delta) and on the TPA action cross section. In toluene, the delta values follow the order of ICT strength. The effect of solvent on delta is nonmonotonic: maximum delta was measured in an intermediate polarity solvent (THF) and was lowest in water. We failed to find a correlation between the observed solvent effect and previous theoretical predictions. Hydrogen bonding to the donor groups and aggregation of the optical units in water, which are not included in calculational analysis, may be responsible for the discrepancies between experimental results and theory.
The molecular weight of a conjugated polymer is one of the key factors determining the electrical, morphological, and mechanical properties as well as its solubility in organic solvents and miscibility with other polymers. In this study, a series of semicrystalline poly[(2,5-bis(2-hexyldecyloxy)phenylene)-alt-(5,6-difluoro-4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole)] (PPDT2FBT) polymers with different number-average molecular weights (M(n)'s) (PPDT2FBT(L), M(n) = 12 kg/mol; PPDT2FBT(M), M(n) = 24 kg/mol; PPDT2FBT(H), M(n) = 40 kg/mol) were synthesized, and their photovoltaic properties as electron donors for all-polymer solar cells (all-PSCs) with poly[[N,N'-bis(2-octyldodecyl)-napthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)] (P(NDI2OD-T2)) acceptor were studied. The M(n) effect of PPDT2FBT on the structural, morphological, electrical, and photovoltaic properties was systematically investigated. In particular, tuning the M(n) induced dramatic effects on the aggregation behaviors of the polymers and their bulk heterojunction morphology of all-PSCs, which was thoroughly examined by grazing incident X-ray scattering, resonant soft X-ray scattering, and other microscopy measurements. High M(n) PPDT2FBT(H) promoted a strong "face-on" geometry in the blend film, suppressed the formation of an excessively large crystalline domain, and facilitated molecularly intermixed phases with P(NDI2OD-T2). Therefore, the optimized all-PSCs based on PPDT2FBT(H)/P(NDI2OD-T2) showed substantially higher hole and electron mobilities than those of PPDT2FBT(L)/P(NDI2OD-T2), leading to a power conversion efficiency exceeding 5%, which is one of the highest values for all-PSCs reported thus far.
We synthesized Ni/Pd core/shell nanoparticles from the consecutive thermal decomposition of metal-surfactant complexes. The nanoparticle catalyst was atom-economically applied for various Sonogashira coupling reactions.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.