A key enabling technology to effective on/off valve based control of hydraulic systems is the high speed on/off valve. High speed valves improve system efficiency for a given PWM frequency, offer faster control bandwidth, and produce smaller output pressure ripples. Current valves rely on the linear translation of a spool or poppet to meter flow. The valve spool must reverse direction twice per PWM cycle. This constant acceleration and deceleration of the spool requires a power input proportional to the PWM frequency cubed. As a result, current linear valves are severely limited in their switching frequencies. In this paper, we present a novel fluid driven PWM on/off valve design that is based on a unidirectional rotary spool. The spool is rotated by capturing momentum from the fluid flow through the valve. The on/off functionality of our design is achieved via helical barriers that protrude from the surface of a cylindrical spool. As the spool rotates, the helical barriers selectively channel the flow to the application (on) or to tank (off). The duty ratio is controlled by altering the axial position of the spool. Since the spool no longer accelerates or decelerates during operation, the power input to drive the valve must only compensate for viscous friction, which is proportional to the PWM frequency squared. We predict that our current design, sized for a nominal flow rate of 40l/m, can achieve a PWM frequency of 84Hz. This paper presents our valve concept, design equations, and an analysis of predicted performance. A simulation of our design is also presented.

The majority of hydraulic systems are controlled using a metering valve or the use of variable displacement pumps. Metering valve control is compact and has a high control bandwidth, but it is energy inefficient due to throttling losses. Variable displacement pumps are far more efficient as the pump only produces the required flow, but comes with the cost of additional bulk, sluggish response, and added cost. In a previous paper [1], a hydromechanical analog of an electronic switch-mode power supply was proposed to create the functional equivalent of a variable displacement pump. This approach combines a fixed displacement pump with a pulse-width-modulated (PWM) on/off valve, a check valve, and an accumulator. The effective pump displacement can be varied by adjusting the PWM duty ratio. Since on/off valves exhibit low loss when fully open or fully closed, the proposed system is potentially more energy efficient than metering valve control, while achieving this efficiency without many of the shortcomings of traditional variable displacement pumps. The system also allows for a host of programmable features that can be implemented via control of the PWM duty ratio. This paper presents initial experimental validation of the concept as well as an investigation of the system efficiency. The experimental apparatus was built using available off-the-shelf components and uses a linear proportional spindle valve as the PWM valve. Experimental results confirm that the proposed approach can achieve variable control function more efficiently than a valve controlled system, and that by increasing the PWM frequency and adding closed-loop control can decrease system response times and of the output ripple magnitude. Sources of inefficiency and their contributions are also investigated via modeling, simulation and are validated by experiments. These indicate design parameters for improving inefficiency.

Efficient high-speed on/off valves are an enabling technology for applying digital control techniques such as pulse-width-modulation (PWM) to hydraulic systems. Virtually variable displacement pumps (VVDPs) are one application where variable displacement functionality is attained using a fixed-displacement pump paired with an on/off valve and an accumulator. High-speed valves increase system bandwidth and reduce output pressure ripple by enabling higher switching frequencies. In addition to fast switching, on/off valves should also have small pressure drop and low actuation power to be effective in these applications. In this paper, a new unidirectional rotary valve designed for PWM is proposed. The valve is unique in utilizing the hydraulic fluid flowing through it as a power source for rotation. An unoptimized prototype capable of high flow rate (40 lpm), high speed (2.8 ms transition time at 100 Hz PWM frequency), and low pressure drop (0.62 MPa), while consuming little actuation power (<0.5% full power or 30 W, scavenged from fluid stream), has been constructed and experimentally validated. This paper describes the valve design, analyzes its performance and losses, and develops mathematical models that can be used for design and simulation. The models are validated using experimental data from a proof-of-concept prototype. The valve efficiency is quantified and suggestions for improving the efficiency in future valves are provided.The test stand reservoir is unsealed, contains no baffling, and the return lines are not submerged and are located near the pump inlet. As a result, splashing occurs in the oil at the PWM frequency due to the tank line.

Efficient high-speed on/off valves are a critical technology for enabling digital control of hydraulic systems via pulse-width-modulation (PWM). High-speed valves, when used in virtually variable displacement pumps (VVDP), increase system bandwidth and reduce output pressure ripple by enabling higher PWM frequencies. Our approach to achieving high speed and large flow area with low actuation power is a unidirectional rotary valve designed specifically for PWM. In comparison to conventional valves, the rotary valve reduces valve actuation power from a cubic dependence on PWM frequency to a square dependence by eliminating motion reversals during transition. This paper presents experimental data that validates the rotary valve concept, valve design equations, and dynamic model of a rotary valve based VVDP. Our unoptimized prototype exhibits 65% efficiency at 50% displacement and 15Hz PWM frequency while the validated model projects that an optimized valve is capable of achieving 85% efficiency at 15Hz and 73% at 75Hz.

The application of switched mode control to hydraulic systems has the potential of decreasing component complexity, size, and cost. This is accomplished by enabling variable pump or motor functionality using a single on/off valve paired with a compact, inexpensive fixed displacement machine. A 4-way tandem rotary on/off valve is presented in this paper that extends a novel rotary valve concept (experimentally validated for pump applications) to hydraulic pump/motors. The pump/valve system is referred to as a Virtually Variable Displacement Pump/Motor (VVDPM) since the effective displacement of the system is variable and not the physical displacement of the pump itself. This paper investigates the design and efficiency of the proposed rotary valve when utilizing the VVDPM on a light weight powersplit hydraulic hybrid passenger vehicle that is driven over a standard federal drive cycle. Simulated VVDPM efficiency maps are presented for motoring and pumping and the cycle efficiency of an optimized VVDPM is compared to that of a typical bent axis unit. Vehicle fuel economy is also explored through simulation.