HTS flux pumps enable superconducting currents to be directly injected into a magnet coil without the requirement for thermally-inefficient current leads. Here, we present results from an experimen tal mechanically-rotating HTS flux pump employing a coated-conductor stator and operated at 77 K. We show the effect of varying the size of the flux gap between the rotor magnets and coated conductor stator from 1 mm to 7.5 mm. This leads to a corresponding change in the peak applied perpendicular magnetic field at the stator from approximately 350 mT to 50 mT. We observe that our experimental device ceases to maintain a measurable output at flux gaps above 7.5 mm, which we attribute to the presence of screening currents in the stator wire.We show that our mechanically-rotating flux pump is well described by a simple circuit model which enables the output performance to be described using two simple parameters, the open-circuit voltage Voc and the internal resistance, Rd. Both of these parameters are found to be directly proportional to magnet-crossing frequency and decrease with increasing flux gap. We show that the trend in Rd can be understood by considering the dynamic resistance experienced at the stator due to the oscillating amplitude of the applied rotor field. We adopt a literature model for the dynamic resistance within our coated-conductor stator and show that this gives good agreement with the experimentally measured internal resistance of our flux pump.

HTS synchronous generators, in which the rotor coils are wound from high-T c superconducting wire, are exciting attention due to their potential to deliver very high torque and power densities. However, injection of the large DC currents required by the HTS rotor coils presents a technical challenge. In this paper we discuss the development of a brushless HTS exciter which operates across the cryostat wall to inject a superconducting DC current into the rotor coil circuit. This approach fundamentally alters the thermal load upon the cryogenic system by removing the need for thermally inefficient normal-conducting current leads. We report results from an experimental laboratory device and show that it operates as a constant voltage source with an effective internal resistance. We then discuss the design of a prototype HTS-PM exciter based on our experimental device, and describe its integration with a demonstration HTS generator. This 200 RPM, 10 kW synchronous generator comprises eight double pancake HTS rotor coils which are operated at 30 K, and are energised to 1.5 T field through the injection of 85 A per pole. We show how this excitation can be achieved using an HTS-PM exciter consisting of 12 stator poles of 12 mm YBCO coated-conductor wire and an external permanent magnet rotor. We demonstrate that such an exciter can excite the rotor windings of this generator without forming a thermal-bridge across the cryostat wall. Finally, we provide estimates of the thermal load imposed by our prototype HTS-PM exciter on the rotor cryostat. We show that duty cycle operation of the device ensures that this heat load can be minimised, and that it is substantially lower than that of equivalently-rated conventional current leads.

No abstract

No abstract

No abstract

High Temperature Superconductor (HTS) flux pumps enable large currents to be injected into a superconducting coil without requiring normal-conducting current leads. We present results from an experimental axial-type HTS rotating flux pump which employs a ferromagnetic circuit to focus incident flux upon a coated-conductor (CC) stator wire. We show that this device can inject currents of > 50 A into an HTS coil at 77 K, and is capable of operating at flux gaps greater than 18 mm. Accommodating a cryostat wall within this flux gap will enable future flux pump designs, in which all moving parts are located outside the cryostat.

YBCO or REBCO coated conductor (2G) materials are developed for their superior performance at high magnetic field and temperature. Power system applications based on high temperature superconducting (HTS) 2G wire technology are attracting attention, including large-scale wind power generators. In particular, to solve problems associated with the foundations and mechanical structure of offshore wind turbines, due to the large diameter and heavy weight of the generator, an HTS generator is suggested as one of the key technologies. Many researchers have tried to develop feasible large-scale HTS wind power generator technologies. In this paper, a study on the required performance of a 2G HTS wire for large-scale wind power generators is discussed. A 12 MW class large-scale wind turbine and an HTS generator are designed using 2G HTS wire. The total length of the 2G HTS wire for the 12 MW HTS generator is estimated, and the essential prerequisites of the 2G HTS wire based generator are described. The magnetic field distributions of a pole module are illustrated, and the mechanical stress and strain of the pole module are analysed. Finally, a reasonable price for 2G HTS wire for commercialization of the HTS generator is suggested, reflecting the results of electromagnetic and mechanical analyses of the generator.

No abstract