Vertical component of seismic excitations tremendously affects the performance of bridges during the earthquakes. Several conducted studies identified the lack of engineering attention to the vertical seismic excitation as the main reason of various considerable bridge damages during the past earthquakes. Thus, in this article, an innovative system with superelastic properties is proposed for retrofitting and also new design of the bridges which can simultaneously mitigate the effects of vertical and horizontal seismic excitations. In order to investigate the efficiency of the new system, an evaluation is performed through many nonlinear time history analyses on a three-dimensional model of a detailed multi-span simply supported bridge using a suite of representative ground motions of the bridge region. The analyses are conducted separately on the pertinent issues that affect the performance of the new proposed system. As a part of the study, to identify the sensitivity of the new system and evaluate the overall seismic performance, several assessment parameters are utilized. The results show that the proposed system is efficient for reducing bridge responses as well as improving nonlinear performance of the columns during vertical and horizontal seismic excitations.
This study focuses on two separate investigations of the main aging mechanisms: alkali–silica reactivity (ASR) and the corrosion of reinforcing steel (rebar) concrete, both of which may result in a premature failure to meet the serviceability or strength requirements of a concrete structure. However, these processes occur very slowly, spanning decades. The impact of direct chemical additives to fresh concrete to accelerate ASR and the corrosion of reinforcing steel on the fresh and hardened properties of the ensuing material are investigated to inform the potential use of chemicals in large-scale studies. The deterioration of reinforced concrete (RC) is determined by means of expansion, cracking, bulk diffusivity and surface resistivity measurements, and compressive, split tensile and flexural strength tests. The results indicate that the addition of sodium hydroxide and calcium chloride can effectively accelerate the crack formation and propagation in concrete due to ASR and the corrosion of rebar, respectively. The ASR-induced cracks maintained a constant crack width from 0.05 mm to 0.1 mm over the measurement period regardless of the intensity of aging acceleration. Adding 4% chloride by weight of cement for accelerating rebar corrosion resulted in an average crack that was 82% larger than in the case of ASR accelerated with the addition of sodium hydroxide. The addition of alkali resulted in an increase in early-age (7-day) strength. At a total alkali loading of 2.98 kg/m3, 3.84 kg/m3 and 5.57 kg/m3, the 28-day compressive strength of concrete decreased by 3%, 10% and 24%, respectively. Similarly, a higher early-age strength and a lower later-age strength was observed for the concrete in the presence of corrosive calcium chloride. The results from this research are expected to inform future studies on the long-term performance of RC structures under accelerated ASR and corrosion.
Superelastic alloy (SEA) bars are widely used in structures subjected to moderate and strong earthquakes. Compared with conventional nickel-titanium (NiTi) SEAs, Cu-Al-Mn (CAM) SEAs has received increasing attention recently due to their cost-effectiveness and easier machinability. The authors’ previous research showed that despite their lower strength and limitations in the maximum length, the CAM SEAs have comparable superelastic strain recovery, a wider temperature range, and superior strain rate stability compared to NiTi SEAs. However, the previous research was limited to a few specimens and only conducted to a few hundred cycles without considering the full deterioration in the material properties. Besides, the existing research on CAM SEA was only limited to small sample sizes at room temperature, while the fatigue performance of large diameter CAM SEAs under low and high temperatures relevant for civil engineering structures has not been reported. To fill this knowledge gap, low-cycle fatigue performance of 20 mm diameter CAM SEAs was studied at room temperature 25℃, low temperature, -40℃, and high temperature, 50℃. Both single crystal and polycrystal CAM SEA were investigated to determine their feasibility as concrete reinforcement under repeated high strain loading cycles expected during an earthquake. Strain cycles up to 50,000 have been applied at a tensile strain amplitude of 5%. Variations in the superelastic properties were observed and analyzed, including the stress-strain curves, elastic modulus, transformation stresses, damping ratio and recovery strain. Stable hysteresis has been observed for cycles exceeding tens of thousands at all temperatures demonstrating the suitability of CAM SEAs for seismic applications in civil engineering structures.
Considering the seismic ground motions as the excitations in only two principal horizontal directions of the bridges and ignoring the third vertical direction is a disregard for the seismic conditions of the region and the bridge distance from epicenter. Numerous cases of substantial damages have been reported among the bridges tremendously suffered from being exposed to the simultaneous three-directional seismic ground motions. Besides the significant compression and tension damages in the columns due to the presence of vertical excitation, it could lead to unexpected shear and flexural failures in the columns and other components as well. Because the axial force variation in the columns due to three-directional excitations, could affect the demands and capacities of the bridge’s components. With respect to this issue, several studies on the bridge damages during the earthquakes have urged researchers to offer efficient methods for bridges handling of the three-directional seismic excitations. Thus, this paper presents and evaluates a superelastic based system for designing as well as retrofitting the multi-span continuous (MSC) bridges that can cope with two- and three-directional seismic excitations. Efficiency evaluation of the proposed system is conducted through various nonlinear time history analyses on a three-dimensional model of a detailed MSC bridge using a suite of developed ground motions for the bridge region. Also, all the analyses are fulfilled based on variation of one influential design characteristic of the proposed system in order to achieve the optimal design. Several pertinent assessment parameters are used during the evaluation of the proposed system. Finally, the efficiency of the new system subjected to the vertical and horizontal seismic excitations is confirmed according to reduction of the bridge responses and improvement in nonlinear performance of the columns in comparison with the as-built bridge results.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.