The microstructure and mechanical performance of wood-based filament is investigated in the case of Fused Deposition Modelling (FDM) technique using experimental and numerical approaches. The printing process of wood-PLA/PHA is conducted by varying the printing temperature, typically from 210 °C to 250 °C. The filament temperature during the laying down is measured using infra-red camera to study the thermal cycling. In addition, X-ray micro-tomography is used to evaluate the material arrangement of printed wood-PLA/PHA at different length scales. Tensile experiments are performed to rank the loss in mechanical performance with respect to the filament properties. Finally, finite element computation is considered to predict the tensile behaviour based on the implementation of the real 3D microstructure issued from X-ray micro-tomography. The results show that the wood-based filament is printable over a wide range of temperatures and exhibits a marked heat accumulation tendency at high printing temperatures. However, the limited gain in tensile performance at these temperatures makes 220 °C an optimal choice for printing wood-based filament. The elongation at break of 3D-printed wood-PLA/PHA is remarkably similar to the results observed for the filament. Finite element computation reveals that despite this apparent similarity, the associated deformation mechanisms are different.

-Three-dimensional printing offers varied possibilities of design that can be bridged to optimisation tools. In this review paper, a critical opinion on optimal design is delivered to show limits, benefits and ways of improvement in additive manufacturing. This review emphasises on design constrains related to additive manufacturing and differences that may appear between virtual and real design. These differences are explored based on 3D imaging techniques that are intended to show defect related processing. Guidelines of safe use of the term ''optimal design'' are derived based on 3D structural information.

Polyethylene terephthalate glycol (PETG) is a thermoplastic formed by polyethylene terephthalate (PET) and ethylene glycol and known for his high impact resistance and ductility. The printability of PETG for fused deposition modelling (FDM) is studied by monitoring the filament temperature using an infra-red camera. The microstructural arrangement of 3D printed PETG is analysed by means of X-ray micro-tomography and tensile performance is investigated in a wide range of printing temperatures from 210 °C to 255 °C. A finite element model is implemented based on 3D microstructure of the printed material to reveal the deformation mechanisms and the role of the microstructural defects on the mechanical performance. The results show that PETG can be printed within a limited range of printing temperatures. The results suggest a significant loss of the mechanical performance due to the FDM processing and particularly a substantial reduction of the elongation at break is observed. The loss of this property is explained by the inhomogeneous deformation of the PETG filament. X-ray micro-tomography results reveal a limited amount of process-induced porosity, which only extends through the sample thickness. The FE predictions point out the combination of local shearing and inhomogeneous stretching that are correlated to the filament arrangement within the plane of construction.

No abstract

No abstract

Fused deposition modeling (FDM) is one of the most popular additive manufacturing techniques for polymers. Despite the numerous works on the printability of various types of polymers, there is a lack in understanding the role of the microstructure on the mechanical performance of printed parts. This work aims at addressing this particular point for the case of a polymer that did not receive much attention, namely acrylonitrile styrene acrylate or ASA. This study emphasizes on the effect of the printing temperature on thermal and mechanical performance of printed ASA using differential scanning calorimetry, infra‐red measurements, mechanical testing, X‐ray micro‐tomography, and finite element computation. The experimental results demonstrate a narrow window of printability of ASA based on the thermal response of this polymer during the laying down process. In addition, both experimental and numerical results show an evident loss in the performance that represents one third of the performance of the raw material. Despite this loss, the limited amount of generated porosity and the level of tensile strength of ASA make it a good choice as a feedstock material for FDM compared to other polymers such as acrylonitrile butadiene styrene.

International audienceOur concern is to reveal the extent of structural imperfections of Additive Manufacturing (AM) by considering 3D imaging technique based on X-ray micro-tomography. Blocks of Acrylonitrile Butadiene Styrene (ABS) polymer are processed using Fused Deposition Modelling (FDM) with different printing orienta-tions. Image analysis is applied to the stacks of 3D printed blocks to quantify structural attributes such as porosity content and connectivity. The results show that pore connectivity represents the most important structural characteristic of FDM. The adopted commercial solution is able to produce acceptable porosity contents below 6% regardless of the printing orientation. Finite element results indicate the presence of expected transverse symmetry. The examination of the extent of such anisotropy is in well agreement with the observed structural imperfections mainly the porosity content. However, these predictions do not match the wide variations in mechanical performance described in the literature. The finite element analysis guides the next research step towards quantification of the imperfect bonding nature between filaments in FDM

Purpose This paper aims to investigate the effect of printing temperature on the thermal and the mechanical behaviour of polylactic acid (PLA)-polyhydroxyalkanoate (PHA) blend printed using fused deposition modelling (FDM). Design/methodology/Approach Because of the use of an infra-red camera, thermal cycling during the laying down is quantified. In addition, X-ray micro-tomography is considered to reveal the microstructural arrangement within the three-dimensional printed material. Tensile loading conditions are used to derive Young’s modulus, tensile strength and fracture toughness, and relate these to the printing temperature. Finite element computation based on three-dimensional microstructure information is used to predict the role of defects on the tensile performance. Findings The results show a remarkable cohesive structure of PLA-PHA, particularly at 240°C. This cohesive structure is explained by the ability to ensure heat accumulation during laying down as evidenced by the nature of thermal cycling. The printing temperature is found to be a key factor for tuning the ductility of the printed PLA-PHA allowing full restoration of tensile strength at high printing temperature. Originality/value This study reports new results related to the thermo-mechanical behaviour of PLA-PHA that did not receive much attention in three-dimensional printing despite its potential as a candidate for pharmacological and medical applications. This study concludes by a wide range of possible printing temperatures for PLA-PHA and a remarkable low porosity generated by FDM.