This study describes the relationship between the solubility of glycinin, a major soy protein, and its structural properties at a quaternary, tertiary, and secondary folding level under conditions representative for food products. When the ionic strength is lowered from 0.5 to 0.2 or 0.03, the basic polypeptides shift more to the exterior of the glycinin complex, as determined at pH 7.6 by labeling solvent-exposed lysines, supported by the study of the proteolytic action of clostripain on glycinin. This structural reorganization caused the pH of minimal solubility to shift to higher values. Ultracentrifugational analysis shows that at pH 7.6 and an ionic strength of 0.5 glycinin forms hexameric complexes (11S), whereas at pH 3.8 and at an ionic strength of 0.03 glycinin exists as trimers (7S). Intermediate situations are obtained by modulation of pH and ionic strength. The observed quaternary dissociation correlates with an increased amount of nonstructured protein at a secondary level and with changes in tertiary folding as determined using circular dichroism. Tryptophan fluorescence shows no significant structural changes for different ionic strengths but demonstrates a more tightly packed fluorophore environment when the pH is lowered from 7.6 to 3.8.

Ara h 1, a major peanut allergen was isolated, and its structure on secondary, tertiary, and quaternary level at ambient temperature was investigated using spectroscopic and biochemical techniques. Ara h 1 appeared to be a highly structured protein on a secondary level, possesses a clear tertiary fold, and is present as a trimeric complex. Heat treatment of purified Ara h 1 results in an endothermic, irreversible transition between 80 and 90°C, leading to an increase in ␤-structures and a concomitant aggregation of the protein. Ara h 1 from peanuts that were heat-treated prior to the purification procedure exhibited a similar denatured state with an increased secondary folding and a decreased solubility. The effect of heat treatment on the in vitro allergenic properties of Ara h 1 was investigated by means of a fluid-phase IgE binding assay using serum from patients with a clinically proven peanut allergy. Ara h 1 purified from peanuts heated at different temperatures exhibited IgE binding properties similar to those found for native Ara h 1, indicating that the allergenicity of Ara h 1 is heat-stable. We conclude that the allergenicity of Ara h 1 is unaffected by heating, although native Ara h 1 undergoes a significant heat-induced denaturation on a molecular level, indicating that the recognition of conformational epitopes of Ara h 1 by IgE either is not a dominant mechanism or is restricted to parts of the protein that are not sensitive to heat denaturation.

Aqueous lubrication is currently at the forefront of tribological research due to the desire to learn and potentially mimic how nature lubricates biotribological contacts. We focus here on understanding the lubrication properties of naturally occurring polysaccharides in aqueous solution using a combination of tribology, adsorption, and rheology. The polysaccharides include pectin, xanthan gum, gellan, and locus bean gum that are all widely used in food and nonfood applications. They form rheologically complex fluids in aqueous solution that are both shear thinning and elastic, and their normal stress differences at high shear rates are found to be characteristic of semiflexible/rigid molecules. Lubrication is studied using a ball-on-disk tribometer with hydrophobic elastomer surfaces, mimicking biotribological contacts, and the friction coefficient is measured as a function of speed across the boundary, mixed, and hydrodynamic lubrication regimes. The hydrodynamic regime, where the friction coefficient increases with increasing lubricant entrainment speed, is found to depend on the viscosity of the polysaccharide solutions at shear rates of around 10(4) s(-1). The boundary regime, which occurs at the lowest entrainment speeds, depends on the adsorption of polymer to the substrate. In this regime, the friction coefficient for a rough substrate (400 nm rms roughness) is dependent on the dry mass of polymer adsorbed to the surface (obtained from surface plasmon resonance), while for a smooth substrate (10 nm rms roughness) the friction coefficient is strongly dependent on the hydrated wet mass of adsorbed polymer (obtained from quartz crystal microbalance, QCM-D). The mixed regime is dependent on both the adsorbed film properties and lubricant's viscosity at high shear rates. In addition, the entrainment speed where the friction coefficient is a minimum, which corresponds to the transition between the hydrodynamic and mixed regime, correlates linearly with the ratio of the wet mass and viscosity at ∼10(4) s(-1) for the smooth surface. These findings are independent of the different polysaccharides used in the study and their different viscoelastic flow properties.

In this article we show how various degrees of glycosylation can be used to control the thermal stability of proteins. The primary amines of beta-lactoglobulin were glycosylated with glucose or fructose within a range of non-denaturing reaction parameters. The modified fractions were characterized and analyzed for structural stability and hydrophobic exposure. The modification procedure gave rise to the production of glycoproteins with a well-defined Gaussian distribution, where glucose appeared more reactive than fructose. The integrity of the secondary, tertiary, and quaternary structures remained unaffected by the modification procedure. However, upon heating the stability of the modified fractions increased up to 6 K. Here we demonstrate the effects on the thermodynamic properties of proteins by glycosylation; this work serves as a first step in understanding and controlling the process underlying aggregation of glycosylated proteins.

No abstract

No abstract

No abstract

There is a large interest in mixed protein/polysaccharide layers at air-water and oil-water interfaces because of their ability to stabilize foams and emulsions. Mixed protein/polysaccharide adsorbed layers at air-water interfaces can be prepared either by adsorption of soluble protein/polysaccharide complexes or by sequential adsorption of complexes or polysaccharides to a previously formed protein layer. Even though the final protein and polysaccharide bulk concentrations are the same, the behavior of the adsorbed layers can be very different, depending on the method of preparation. The surface shear modulus of a sequentially formed beta-lactoglobulin/pectin layer can be up to a factor of 6 higher than that of a layer made by simultaneous adsorption. Furthermore, the surface dilatational modulus and surface shear modulus strongly (up to factors of 2 and 7, respectively) depend on the bulk -lactoglobulin/pectin mixing ratio. On the basis of the surface rheological behavior, a mechanistic understanding of how the structure of the adsorbed layers depends on the protein/polysaccharide interaction in bulk solution, mixing ratio, ionic strength, and order of adsorption to the interface (simultaneous or sequential) is derived. Insight into the effect of protein/polysaccharide interactions on the properties of adsorbed layers provides a solid basis to modulate surface rheological behavior.