This work investigates the influence of deleterious phases precipitation on the corrosion resistance of two wrought superduplex stainless steels UNS S32750 with similar composition, but different grain sizes. Isothermal treatments were carried out to introduce different amounts of deleterious phases, such as chi (χ), sigma (σ) and secondary austenite (γ 2 ). The specimens were tested by double loop electrochemical potentiodynamic reactivation test (DL-EPR). The kinetics of precipitation in the two steels was different due to the difference of the grain sizes. The results show a correlation between the sensitization degrees, measured by DL-EPR, with the amount of deleterious phases precipitated.
Resumo
O presente trabalho apresenta os resultados da caracterização e avaliação da resistência à corrosão de uma junta soldada correspondente a uma tubulação de aço inoxidável duplex (AID) UNS
Tempering is the final heat treatment applied to martensitic steels. In conventional martensitic stainless steels or in the newly developed supermartensitic grades, the mechanical properties are strongly influenced by tempering. In the present work, several tempering treatments were performed in a Ti alloyed supermartensitic stainless steel. Tensile mechanical properties, hardness and impact toughness were measured and correlated to microstructural features. Microstructural analysis was conducted in a field emission gun scanning electron microscope and also by magnetic measurements. The ductility parameters continuously increased with tempering temperature, while yield and ultimate strength decreased. Secondary hardening and temper embrittlement were observed by hardness and low temperature impact tests respectively, while tensile tests were not sensitive to these phenomena.
Resumo
Os aços inoxidáveis Duplex (AID) aliam uma excelente resistência à corrosão com elevada resistência mecânica devido à fina microestrutura bifásica composta por quantidades similares de ferrita (d) e austenita (g).
The tensile mechanical behaviour of hybrid jute/cotton fabric reinforced polyester composites was evaluated. Three fabric configurations, with varying jute weight fractions, were used and five stacking sequences were analysed, namely: [0]; [0/90]; [0/90/0]; [90/0/90] and [0/90/0/90]. The data suggest that differences on the areal density of the fabrics were of minor importance to the tensile behaviour of the composites with jute fibres aligned to the loading direction, [0]. The results obtained for the other configurations -with [90]layers -were strongly influenced by the lack of resin impregnation inside the tow of the fibre, by the weak jute/polyester matrix interface and by the presence of jute fibres aligned perpendicularly to the loading direction. For these stacking sequences, the results obtained were dominated by the maximum strain sustained at the jute/polyester interface. Cotton fibres were shown to be non-reinforcing, and to act only as a convenient ancillary fibre aiding at the fabric manufacture.
Os aços inoxidáveis superduplex (AISD) são materiais que aliam altos valores de resistência mecânica com elevados níveis de resistência à corrosão. Por tal motivo, esta família de aços inoxidáveis é muito utilizada em componentes de processo na indústria offshore. No entanto, existem grandes desafios na soldagem destes materiais em termos de produtividade e custos mantendo-se a qualidade da junta produzida. Atualmente, a proteção gasosa da raiz é efetuada até o último passe de acabamento na soldagem durante a pré-montagem e montagem de tubulações de AISD em plataformas offshore. Neste tipo de proteção são usualmente empregados os gases hélio, argônio e nitrogênio, ou misturas destes. O nitrogênio é tipicamente adicionado no gás de proteção em teores de até 3% de modo a promover a estabilização da fase austenítica na superfície da raiz da solda. Devido ao alto custo do gás de proteção utilizado, é necessário determinar o passe ou camada na qual a proteção gasosa na raiz seja efetiva em termos das propriedades mecânicas e da resistência à corrosão, considerando ser esta uma região crítica, que ficará em contato com o fluido operante durante o serviço do componente. Neste sentido, o presente trabalho apresenta os resultados da influência da utilização de gás de purga na raiz de juntas soldadas correspondente a uma tubulação de aço inoxidável superduplex (AISD) UNS S32750 de 9 mm de espessura de parede soldada pelo processo de soldagem TIG (GTAW). Foram avaliados o ciclo térmico, o teor de nitrogênio e a tenacidade ao impacto da raiz da solda em função do aporte térmico para diversas juntas soldadas com diferentes níveis de proteção gasosa na raiz. Deste modo, o presente trabalho tem como objetivo a redução de custos na soldagem de tubulações indicando até qual camada é requerida a proteção gasosa na raiz em função do aporte de calor empregado.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.