The aim of this study was to determine the reproducibility, reliability and validity of measurements in digital models compared to plaster models. Fifteen pairs of plaster models were obtained from orthodontic patients with permanent dentition before treatment. These were digitized to be evaluated with the program Cécile3 v2.554.2 beta. Two examiners measured three times the mesiodistal width of all the teeth present, intercanine, interpremolar and intermolar distances, overjet and overbite. The plaster models were measured using a digital vernier. The t-Student test for paired samples and interclass correlation coefficient (ICC) were used for statistical analysis. The ICC of the digital models were 0.84 ± 0.15 (intra-examiner) and 0.80 ± 0.19 (inter-examiner). The average mean difference of the digital models was 0.23 ± 0.14 and 0.24 ± 0.11 for each examiner, respectively. When the two types of measurements were compared, the values obtained from the digital models were lower than those obtained from the plaster models (p < 0.05), although the differences were considered clinically insignificant (differences < 0.1 mm). The Cécile digital models are a clinically acceptable alternative for use in Orthodontics.

This study evaluated the relationship among malocclusion, number of occlusal pairs, masticatory performance, masticatory time and masticatory ability in completely dentate subjects. Eighty healthy subjects (mean age = 19.40 ± 4.14 years) were grouped according to malocclusion diagnosis (n = 16): Class I, Class II-1, Class II-2, Class III and Normocclusion (control). Number of occlusal pairs was determined clinically. Masticatory performance was evaluated by the sieving method, and the time used for the comminute test food was registered as the masticatory time. Masticatory ability was measured by a dichotomic self-perception questionnaire. Statistical analysis was done by one-way ANOVA, ANOVA on ranks, Chi-Square and Spearman tests. Class II-1 and III malocclusion groups presented a smaller number of occlusal pairs than Normocclusion (p < 0.0001), Class I (p < 0.001) and II-2 (p < 0.0001) malocclusion groups. Class I, II-1 and III malocclusion groups showed lower masticatory performance values compared to Normocclusion (p < 0.05) and Class II-2 (p < 0.05) malocclusion groups. There were no differences in masticatory time (p = 0.156) and ability (χ 2 = 3.58/p = 0.465) among groups. Occlusal pairs were associated with malocclusion (rho = 0.444/p < 0.0001) and masticatory performance (rho = 0.393/p < 0.0001), but malocclusion was not correlated with masticatory performance (rho = 0.116/p = 0.306). In conclusion, masticatory performance and ability were not related to malocclusion, and subjects with Class I, II-1 and III malocclusions presented lower masticatory performance because of their smaller number of occlusal pairs.

OBJECTIVE: Define and compare numbers and types of occlusal contacts in maximum intercuspation. METHODS: The study consisted of clinical and photographic analysis of occlusal contacts in maximum intercuspation. Twenty-six Caucasian Brazilian subjects were selected before orthodontic treatment, 20 males and 6 females, with ages ranging between 12 and 18 years. The subjects were diagnosed and grouped as follows: 13 with Angle Class I malocclusion and 13 with Angle Class II Division 1 malocclusion. After analysis, the occlusal contacts were classified according to the established criteria as: tripodism, bipodism, monopodism (respectively, three, two or one contact point with the slope of the fossa); cuspid to a marginal ridge; cuspid to two marginal ridges; cuspid tip to opposite inclined plane; surface to surface; and edge to edge. RESULTS: The mean number of occlusal contacts per subject in Class I malocclusion was 43.38 and for Class II Division 1 malocclusion it was 44.38, this difference was not statistically significant (p>0.05). CONCLUSIONS: There is a variety of factors that influence the number of occlusal contacts between a Class I and a Class II, Division 1 malocclusion. There is no standardization of occlusal contact type according to the studied malocclusions. A proper selection of occlusal contact types such as cuspid to fossa or cuspid to marginal ridge and its location in the teeth should be individually defined according to the demands of each case. The existence of an adequate occlusal contact leads to a correct distribution of forces, promoting periodontal health

Objective: The objective of this research was to demonstrate the efficiency of the overbite depth indicator (ODI) and the anteroposterior dysplasia indicator (APDI) from Kim’s cephalometric analysis, regarding the determination of the vertical and sagittal patterns of Latin American individuals. Methods: Two hundred lateral cephalometric radiographs were selected and divided into four study groups, with 50 radiographs each, for carrying out a cross-sectional study. The control group included radiographs of balanced individuals, and the other three groups had lateral cephalometric radiographs of subjects with Class I, II and III malocclusions and with skeletal open bite. After the pilot test was performed to calibrate the investigator, the ODI and APDI were measured. Descriptive statistics were performed and the one-way ANOVA with post-hoc Tukey HSD, or Kruskal-Wallis and Mann-Whitney U-test were used. Also a multiple linear regression was employed. Results: Statistically significant differences were found for the ODI of all groups (p< 0.001), except between Class I group (65.87 ± 4.26) and Class II open bite group (67.19 ± 3.58), both with similar values to each other. For APDI, statistically significant differences were also found for all groups (p< 0.001). However, no statistically significant differences were found between the balanced group (83.18 ± 1.71) and Class I group with skeletal open bite (81.78 ± 2.69). Conclusions: ODI and APDI are reliable indicators to evaluate the sagittal and vertical patterns of an individual, demonstrating their efficiency when a Latin American population was evaluated.

No abstract

No abstract

No abstract

Establecer los parámetros de normalidad de los tejidos blandos en una población adulta peruana con características cefalométricas armónicas, según el análisis de Holdaway. METODOLOGÍA: La muestra estuvo conformada por 25 radiografías cefalométricas de pacientes de 20-40 años de edad con perfil facial armónico, de clase I, en los cuales se midió el análisis cefalométrico de Holdaway y se comparó con las normas existentes. RESULTADOS: La mayoría de las medidas lineales y angulares coincidieron con las normas de Holdaway, excepto la prominencia nasal en que la muestra de peruanos presenta una nariz más pequeña(12.34mm ±3.03), el ángulo H presenta una mayor prominencia del labio superior(14.08 ±2.41) y la medida del labio inferior a la línea H muestra una posición labial inferior aumentada (1.44 ±0.95). CONCLUSIÓN: El análisis de Holdaway puede ser aplicado en sujetos peruanos; ya que, los valores en pacientes armónicos no difieren estadísticamente de los valores propuestos en su análisis, excepto en la prominencia nasal, ángulo H y medida del labio inferior a la línea H.