No abstract

The inherent differences in reactivity between activated and non‐activated alkenes prevents copolymerization using established polymer synthesis techniques. Research over the past 20 years has greatly advanced the copolymerization of polar vinyl monomers and olefins. This Review highlights the challenges associated with conventional polymerization systems and evaluates the most relevant methods which have been developed to “bridge the gap” between polar vinyl monomers and olefins. We discuss advancements in heteroatom tolerant coordination–insertion polymerizations, methods of controlling radical polymerizations to incorporate olefinic monomers, as well as combined approaches employing sequential polymerizations. Finally, we discuss state‐of‐the‐art stimuli‐responsive systems capable of facile switching between catalytic pathways and provide an outlook towards applications in which tailored copolymers are ideally suited.

This manuscript is dedicated to Professor Mitsuo Sawamoto's outstanding achievements in polymer chemistry and recognizes his recent retirement from 40 years of exceptional service to Kyoto University.To address this challenge and provide insight into photo-CRP processes, a recently developed in situ NMR spectroscopy method is utilized to evaluate temporal control for a selection of widely studied photo-CRP processes (see Fig. 1 and Supplementary Information Figure S1 for a Additional supporting information may be found in the online version of this article.

As a method for overcoming the challenge of rigorous deoxygenation in copper‐mediated controlled radical polymerization processes [e.g., atom‐transfer radical polymerization (ATRP)], reported here is a simple Cu0‐RDRP (RDRP=reversible deactivation radical polymerization) system in the absence of external additives (e.g., reducing agents, enzymes etc.). By simply adjusting the headspace of the reaction vessel, a wide range of monomers, namely acrylates, methacrylates, acrylamides, and styrene, can be polymerized in a controlled manner to yield polymers with low dispersities, near‐quantitative conversions, and high end‐group fidelity. Significantly, this approach is scalable (ca. 125 g), tolerant to elevated temperatures, compatible with both organic and aqueous media, and does not rely on external stimuli which may limit the monomer pool. The robustness and versatility of this methodology is further demonstrated by the applicability to other copper‐mediated techniques, including conventional ATRP and light‐mediated approaches.

Usually atom transfer radical polymerization (ATRP) requires various parameters, such as the type of initiator, transition metal, ligand, solvent, temperature, deactivator, added salts and reducing agents, need to be optimised in order to achieve a high degree of control over molecular weight and dispersity. These components play a major role when switching monomers e.g. from acrylic to methacrylic and/or styrenic monomers during the synthesis of homo-and block copolymers as the stability and reactivity of the carbon centered propagating radical dramatically changes. This is a challenge for both "experts" and non-experts as choosing the appropriate conditions for successful polymerization can be time consuming and an arduous task. In this work we describe some universal conditions for the efficacious polymerization of acrylates, methacrylates and styrene (using an identical initiator, ligand, copper salt and solvent) based on commercially available reagents (PMDETA, IPA, Cu(0) wire). The versatility of these conditions is demonstrated by the near quantitative polymerization of these monomer families to yield well-defined materials over a range of molecular weights with low dispersities (~1.1-1.2). The control and high end group fidelity is further exemplified by in situ block copolymerization upon sequential monomer addition for the case of methacrylates and styrene furnishing higher molecular weight copolymers with minimal termination. The facile nature of these conditions, combined with readily available reagents will greatly expand the access and availability of tailored polymeric materials to all researchers.

Atom transfer radical polymerization (ATRP) of acrylamide (AM) has proved challenging, typically exhibiting low conversions and broad molecular weight distributions (MWDs). Herein, we report the synthesis of well-defined polyacrylamide (both homo and block copolymers) via aqueous copper(0)mediated reversible-deactivation radical polymerization (Cu(0)-RDRP), exploiting the in situ disproportionation of Cu(I)Br in the presence of Me 6 Tren to yield insoluble Cu(0) and Cu(II)Br 2 which acts as a deactivator. Careful optimization of the levels of Cu(I)Br and Me 6 TREN allowed for the synthesis of polyacrylamide of a range of molecular weights (DP n = 20−640) proceeding to quantitative conversion within just a few minutes (typically full conversion is attained within 15 min of reaction time) and exhibiting narrow MWDs (Đ as low as 1.09), which represents a significant improvement over transitional-metalmediated approaches previously reported in the literature. This optimized approach was subsequently utilized to perform in situ chain extensions and block copolymerizations with hydroxyethyl acrylamide, yielding block copolymers of low dispersity and quantitative monomer conversions in a time frame of minutes.

Photoinduced metal mediated radical polymerization is a rapidly developing technique which allows for the synthesis of macromolecules with defined molecular weight and narrow molecular weight distributions, although typically exhibiting significant limitations in aqueous media. Herein we demonstrate that the presence of alkali metal halide salts in conjunction with low copper concentration and UV irradiation, allows for the controlled polymerization of water soluble acrylates in aqueous media, yielding narrow molecular weight distributions and high conversions. Despite the aqueous environment which typically compromises polymer end group fidelity, chain extensions have also been successfully performed and different degrees of polymerization were targeted. Importantly, no conversion was observed in the absence of UV light and the polymerization could be switched "on" and "off" upon demand as demonstrated by intermittent light and dark periods and thus allowing access to spatiotemporal control.

Block copolymers form the basis of the most ubiquitous materials such as thermoplastic elastomers, bridge interphases in polymer blends, and are fundamental for the development of high-performance materials. The driving force to further advance these materials is the accessibility of block copolymers, which have a wide variety in composition, functional group content, and precision of their structure. To advance and broaden the application of block copolymers will depend on the nature of combined segmented blocks, guided through the combination of polymerization techniques to reach a high versatility in block copolymer architecture and function. This review provides the most comprehensive overview of techniques to prepare linear block copolymers and is intended to serve as a guideline on how polymerization techniques can work together to result in desired block combinations. As the review will give an account of the relevant procedures and access areas, the sections will include orthogonal approaches or sequentially combined polymerization techniques, which increases the synthetic options for these materials.