No abstract

No abstract

No abstract

Ion-conducting membranes are essential components in many electrochemical devices, but they often add substantial cost, limit performance, and are susceptible to degradation. This work investigates membraneless electrochemical flow cells for hydrogen production from water electrolysis that are based on angled mesh flow-through electrodes. These devices can be fabricated with as few as three parts (anode, cathode, and cell body), reflecting their simplicity and potential for low-cost manufacture. 3D printing was used to fabricate prototype electrolyzers that were demonstrated to be electrolyte agnostic, modular, and capable of operating with minimal product crossover. Prototype electrolyzers operating in acidic and alkaline solutions achieved electrolysis efficiencies of 61.9% and 72.5%, respectively, (based on the higher heating value of H 2 ) when operated at 100 mA cm −2 . Product crossover was investigated using in situ electrochemical sensors, in situ imaging, and by gas chromatography (GC). GC analysis found that 2.8% of the H 2 crossed over from the cathode to the anode stream under electrolysis at 100 mA cm −2 and fluid velocity of 26.5 cm s −1 . Additionally, modularity was demonstrated with a three-cell stack, and high-speed video measurements tracking bubble evolution from electrode surfaces provide valuable insight for the further optimization of electrolyzer design and performance. Solar and wind energy have the potential to power the planet without the environmental impact of fossil fuels, but encounter significant challenges to widespread adoption due to their low capacity factors and inherent intermittency.1 In order to overcome this challenge, affordable grid-scale energy storage technology is needed that can make electricity generation from these technologies more widespread.2 One solution to this issue is to convert excess renewable electricity into stored chemical energy in the form of hydrogen gas (H 2 ), 3 which represents a promising candidate for grid scale energy storage and as a carbon-free replacement of fossil fuels in the transportation and industry sectors. 4 Electrolyzers, which use electricity and water to produce hydrogen and oxygen, are well-established commercially available technologies, 5 but the cost of producing H 2 by water electrolysis is currently too expensive.6-8 Presently, much of the cost of producing H 2 by water electrolysis comes from the price of electricity, 6,8 but as the price of electricity from wind and solar continues to decrease and time-of-use pricing schemes become more prevalent, decreasing the cost of electrolyzer technology will be of great importance to making a renewable hydrogen future a reality.The majority of electrolyzers are based on a design in which the cathode and anode are separated by an ion-conducting membrane or diaphragm. 9 The two most common types of electrolyzers are alkaline and polymer electrolyte membrane (PEM) electrolyzers, which are able to electrolyze alkaline and ultra-pure water, respectively. These electrolyzers are mature t...

This article reviews computational and in situ experimental tools capable of characterizing the properties and performance of photoelectrodes used for solar fuels production with high spatial and temporal resolution.

The development of a novel analytical technique, electrochemical X-ray fluorescence (EC-XRF), is described and applied to the quantitative detection of heavy metals in solution, achieving sub-ppb limits of detection (LOD). In EC-XRF, electrochemical preconcentration of a species of interest onto the target electrode is achieved here by cathodic electrodeposition. Unambiguous elemental identification and quantification of metal concentration is then made using XRF. This simple electrochemical preconcentration step improves the LOD of energy dispersive XRF by over 4 orders of magnitude (for similar sample preparation time scales). Large area free-standing boron doped diamond grown using microwave plasma chemical vapor deposition techniques is found to be ideal as the electrode material for both electrodeposition and XRF due to its wide solvent window, transparency to the XRF beam, and ability to be produced in mechanically robust freestanding thin film form. During electrodeposition it is possible to vary both the deposition potential (Edep) and deposition time (tdep). For the metals Cu(2+) and Pb(2+) the highest detection sensitivities were found for Edep = -1.75 V and tdep (=) 4000 s with LODs of 0.05 and 0.04 ppb achieved, respectively. In mixed Cu(2+)/Pb(2+) solutions, EC-XRF shows that Cu(2+) deposition is unimpeded by Pb(2+), across a broad concentration range, but this is only true for Pb(2+) when both metals are present at low concentrations (10 nM), boding well for trace level measurements. In a dual mixed metal solution, EC-XRF can also be employed to either selectively deposit the metal which has the most positive formal reduction potential, E(0), or exhaustively deplete it from solution, enabling uninhibited detection of the metal with the more negative E(0).

Light-addressable electrochemical sensors (LAESs) are a class of sensors that use light to activate an electrochemical reaction on the surface of a semiconducting photoelectrode. Here, we investigate semiconductor/metal (Schottky) junctions formed between n-type Si and Au nanoparticles as light-addressable electrochemical sensors. To demonstrate this concept, we prepared n-Si/Au nanoparticle Schottky junctions by electrodeposition and characterized them using scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. We found that the sensors behaved almost identically to Au disk electrodes for the oxidation of an outer-sphere redox couple (ferrocene methanol) and two inner-sphere redox couples (potassium ferrocyanide and dopamine). In buffered dopamine solutions, we observed broad linear ranges and submicromolar detection limits. We then used local illumination to generate a virtual array of electrochemical sensors for dopamine as a strategy for circumventing sensor fouling, which is a persistent problem for electrochemical dopamine sensors. By locally illuminating a small portion of the photoelectrode, many measurements of fouling analytes can be made on a single sensor with a single electrical connection by moving the light beam to a fresh area of the sensor. Altogether, these results pave the way for Schottky junction light-addressable electrochemical sensors to be useful for a number of interesting future applications in chemical and biological sensing.

No abstract