The contact problem and stress state for indentation by a flat punch with rounded edges is studied. For the contact problem itself analytical solutions are obtained for both surface pressure and interior stress fields. Cases of normal indentation and frictional contact, the latter in both sliding or partial slip conditions, are all treated. The transition from the Hertzian configuration to the contact between a nominally flat pad and contacting flat surface is discussed, and it is found that the strength of the contact decays surprisingly slowly. Regarding the von Mises yield parameter, there is a range of configurations for which the strength is actually higher than the Hertzian one, and the strength decays only when the corner radii are very small. The present solution is therefore a realistic alternative to the classical rigid-flat punch idealization, and has particular application to fretting fatigue tests.

Complexity of scaffold geometries and biological mechanisms involved in the bone generation process make the design of scaffolds a quite challenging task. The most common approaches utilized in bone tissue engineering require costly protocols and time-consuming experiments. In this study we present an algorithm that, combining parametric finite element models of scaffolds with numerical optimization methods and a computational mechano-regulation model, is able to predict the optimal scaffold microstructure. The scaffold geometrical parameters are perturbed until the best geometry that allows the largest amounts of bone to be generated, is reached. We study the effects of the following factors: (1) the shape of the pores; (2) their spatial distribution; (3) the number of pores per unit area. The optimal dimensions of the pores have been determined for different values of scaffold Young's modulus and compression loading acting on the scaffold upper surface.Pores with rectangular section were predicted to lead to the formation of larger amounts of bone compared to square section pores; similarly, elliptic pores were predicted to allow the generation of greater amounts of bone compared to circular pores. The number of pores per unit area appears to have rather negligible effects on the bone regeneration process. Finally, the algorithm predicts that for increasing loads, increasing values of the scaffold Young's modulus are preferable.The results shown in the article represent a proof-of-principle demonstration of the possibility to optimize the scaffold microstructure geometry based on mechanobiological criteria.

No abstract

No abstract

Functionally Graded Scaffolds (FGSs) are porous biomaterials where porosity changes in space with a specific gradient. In spite of their wide use in bone tissue engineering, possible models that relate the scaffold gradient to the mechanical and biological requirements for the regeneration of the bony tissue are currently missing. In this study we attempt to bridge the gap by developing a mechanobiology-based optimization algorithm aimed to determine the optimal graded porosity distribution in FGSs. The algorithm combines the parametric finite element model of a FGS, a computational mechano-regulation model and a numerical optimization routine. For assigned boundary and loading conditions, the algorithm builds iteratively different scaffold geometry configurations with different porosity distributions until the best microstructure geometry is reached, i.e. the geometry that allows the amount of bone formation to be maximized. We tested different porosity distribution laws, loading conditions and scaffold Young’s modulus values. For each combination of these variables, the explicit equation of the porosity distribution law–i.e the law that describes the pore dimensions in function of the spatial coordinates–was determined that allows the highest amounts of bone to be generated. The results show that the loading conditions affect significantly the optimal porosity distribution. For a pure compression loading, it was found that the pore dimensions are almost constant throughout the entire scaffold and using a FGS allows the formation of amounts of bone slightly larger than those obtainable with a homogeneous porosity scaffold. For a pure shear loading, instead, FGSs allow to significantly increase the bone formation compared to a homogeneous porosity scaffolds. Although experimental data is still necessary to properly relate the mechanical/biological environment to the scaffold microstructure, this model represents an important step towards optimizing geometry of functionally graded scaffolds based on mechanobiological criteria.

Spacedesign is an innovative Mixed Reality (MR) application addressed to aesthetic design of free form curves and surfaces. It is a unique and comprehensive approach which uses task-specific configurations to support the design workflow from concept to mock-up evaluation and review. The first-phase conceptual design benefits from a workbench-like 3-D display for free hand sketching, surfacing and engineering visualization. Semitransparent stereo glasses augment the pre-production physical prototype by additional shapes, textures and annotations. Both workspaces share a common interface and allow collaboration and cooperation between different experts, who can configure the system for the specific task. A faster design workflow and CAD data consistency can be thus naturally achieved. Tests and collaborations with designers, mainly from automotive industry, are providing systematic feedback for this ongoing research. As far as the authors are concerned, there is no known similar approach that integrates the creation and editing phase of 3D curves and surfaces in Virtual and Augmented Reality (VR/AR). Herein we see the major contribution of our new application.

No abstract

No abstract