The final results of radon monitoring in 438 schools located in the province of Lecce (Puglia Region, South Italy) showed an average radon concentration of 215 ± 20 Bq m and that 7% of schools exceeded 500 Bq m, the current Italian action level for radon in workplaces, and consequently required remedial actions. The activity described in the present paper includes the main elements of the remediation project in a subgroup of school buildings. The main radon control systems adopted were sub-slab depressurization (in 57% of schools) and the active ventilation of the crawlspace (in 21% of schools). This experience allows us to put in evidence relevant critical aspects, such as the influence of the karstic nature of the area, the optimization of remediation, the architectural constraints in the case of buildings of architectural or historical interest, which are discussion herein. Moreover, considering the new reference level for radon in workplaces introduced by the new EU Basic Safety Standards, a new analysis of data, achieved in the first survey, highlighted that 20% of schools need to be remediated.

In hot climates tiled pitched roofs significantly reduce the heat transfer across the roof structure, due to the ventilated air layer between tiles and roofing underlay formed by the arrangement of battens and counter-battens supporting the tiles. This so-called Above Sheathing Ventilation (ASV) depends on the air entering and leaving at the eaves, ridge and the gaps between the tiles. With a view towards higher energy savings in space cooling, the natural and forced convection occurring in ASV could be enhanced by increasing the roof air permeability by means of novel tile shapes, as here analysed in two stages.\ud The first stage of designing the new tile shapes was to measure the air permeability for a type of existing tile (Marseillaise style) using an experimental test rig, by monitoring the volumetric flow rate through the tiles over a range of pressure differences across the tiles. Then, a three-dimensional CFD model was implemented to replicate the full test rig geometry, and this was calibrated against the experimental data. In the next stage, the calibration was used to support the design of novel Marseillaise tile shapes, and to compare their performance against existing tiles. Finally, in order to analyse the variation in air flow under typical wind conditions for a pitched roof, a parametric study was undertaken, consisting of 72 scenarios varying wind speed, direction and angle of incidence.\ud An increase in volumetric flow rate through the tiles was found to be related not only to an increase in the open area between tiles, but also to the design of the tile locks. By redesigning the geometry of these locks, whilst still giving consideration to their primary purpose of preventing the ingress of driving rain, it was possible to yield an improvement in air permeability of up to 100% in comparison with the original designs. Additionally, these novel designs were shown to increase the air flow rate as the wind angle moved from being directly up the roof slope around to the side, in contrast to the decrease seen with existing tile shapes

In tiled pitched roofs, a ventilated layer reduces the heat transfer between tiles and roof structure by means of natural and forced convection, thereby also reducing the cooling energy requirement. This effect could be enhanced by increasing the air permeability between the tiles by means of novel tile shapes, as proposed by the HEROTILE European project (LIFE14 CCA/IT/000939), of which this work presents the preliminary analysis supporting the new tile designs.\ud Using an experimental rig, the air pressure difference and the volumetric flow rate between tiles have been measured for an existing Portoghese tile design over a range of pressures. Then, in order to understand the air flows under different conditions, a three-dimensional CFD model has been implemented to recreate the full geometry of the rig. The model was calibrated against the aforementioned experimental results, and run with boundary conditions simulating different wind directions. Even in the low velocities typical of average local wind patterns, the fluid dynamic problem remains complex because of the geometry of the gaps between the tiles. However, it has been possible to assess the coefficient of local head loss and then apply it in an analytical relationship between pressure drop and flow rate, taking into account the open area. The results have shown how the wind direction affects the air permeability and, therefore, important insights have been gathered for the design of novel tiles

The construction sector accounts for more than one-third of the global energy consumption. Ventilated roofs and facades are among the adopted strategies to improve the efficiency of the building envelope: air flowing in cavities under the cladding layer, in fact, is particularly effective in hot summers for the reduction of the incoming heat flow due to solar radiation. Regarding roofs, satisfying results were obtained through the realization of a 5-10 cm air gap under the covering layer which allows better thermal performances of the roof and a reduction of the energy consumption for air conditioning. Although most of products and techniques applied are based on the assumption that air enters only from the eaves line and exits at the ridge one, it is demonstrated that in case of discontinuous mantles, a great contribution derives from air entering from the overlaps. As a matter of fact, air entering from the eaves line is strictly dependent on the wind direction and benefits are evident only when the wind is perpendicular. In all the other cases, buoyancy forces due to air heating under the mantle cannot provide such a consistent contribution. Tiles overlaps’ air permeability allows the wind to enter from multiple directions with consequent greater ventilation of the substrate. Experimental research regarding the performances of pitched tiled roofs was conducted at the TekneHub laboratory of the University of Ferrara and the results are here presented. The tests carried out aimed at investigating the behaviour of different configurations of tiled roofs both from a thermal and an energetic point of view. Three configurations were compared: one was a completely sealed roof (sealed), one had sealed eaves and ridge lines but unsealed tiles overlaps (laid) and the last one was a ventilated roof (vented). The comparison between the sealed and the ventilated roof confirmed the improvement of the performances when in presence of an air cavity. The ventilated roof was then compared to the laid roof to assess the actual contribution of the air permeability of the tiles, and results clearly showed a great contribution, even in case of low wind.

In hot climates, ventilated pitched roofs help dissipating the excess heat, thus reducing the cooling energy demand. The key factor is the so-called Above Sheathing Ventilation (ASV) that depends on the air entering and leaving at the eaves, ridge and the gaps among tiles. A strategy for increasing the ASV is the enhancement of the roof air permeability through the development of new tile shapes, as proposed in the European Life HEROTILE project. The performance of a ventilated pitched roof are experimentally analysed by comparing some covering options: the new tile shape designs against the standard ones, available in the market, and a metal cover. A real scale pitched roof mock-up was built and equipped with a comprehensive monitoring system. The air flow and temperature in the different roof layers, as well as the heat flux passing through the roof and the cooling energy demand, were monitored according to the local weather conditions during the summer season. The analysis showed that the new tile design increases the ASV in comparison with the standard ones, and better thermal performance was achieved by reducing the heat gain due to solar radiation.