This paper introduces simple analytical formulas for the grid impedance of electrically dense arrays of square patches and for the surface impedance of high-impedance surfaces based on the dense arrays of metal strips or square patches over ground planes. Emphasis is on the oblique-incidence excitation. The approach is based on the known analytical models for strip grids combined with the approximate Babinet principle for planar grids located at a dielectric interface. Analytical expressions for the surface impedance and reflection coefficient resulting from our analysis are thoroughly verified by full-wave simulations and compared with available data in open literature for particular cases. The results can be used in the design of various antennas and microwave or millimeter wave devices which use artificial impedance surfaces and artificial magnetic conductors (reflect-array antennas, tunable phase shifters, etc.), as well as for the derivation of accurate higher-order impedance boundary conditions for artificial (high-) impedance surfaces. As an example, the propagation properties of surface waves along the high-impedance surfaces are studied. I. INTRODUCTIONIn this paper we consider planar periodic arrays of infinitely long metal strips and periodic arrays of square patches, as well as artificial high-impedance surfaces based on such grids. [17]. Capacitive strips and square patches have been studied extensively in the literature (e.g., [18]-[20]). However, to the best of the authors' knowledge, there is no known easily applicable analytical model capable of predicting the plane-wave response of these artificial surfaces for large angles of incidence with good accuracy.Models of planar arrays of metal elements excited by plane waves can be roughly split into two categories: computational and analytical methods. Computational methods as a rule are based on the Floquet expansion of the scattered field (see, e.g., [2], [3], [21], [22]). These methods are electromagnetically strict and general (i.e., not restricted to a particular design geometry). Periodicity of the total field in tangential directions allows one to consider the incidence of a plane wave on a planar grid or on a high-impedance surface as a single unit cell problem. The field in the unit cell of the structure can be solved using,

No abstract

The coordinate-transformation-based differential method of Chandezon et al. [J. Opt. (Paris) 11, 235 (1980); J. Opt. Soc. Am. 72, 839 (1982)] (the C method) is one of the simplest and most versatile methods for modeling surface-relief gratings. However, to date it has been used by only a small number of people, probably because, traditionally, elementary tensor theory is used to formulate the method. We reformulate the C method without using any knowledge of tensor, thus, we hope, making the C method more accessible to optical engineers.

HAL is a multi-disciplinary open access archive for the deposit and dissemination of scientific research documents, whether they are published or not. The documents may come from teaching and research institutions in France or abroad, or from public or private research centers. L'archive ouverte pluridisciplinaire HAL, est destinée au dépôt et à la diffusion de documents scientifiques de niveau recherche, publiés ou non, émanant des établissements d'enseignement et de recherche français ou étrangers, des laboratoires publics ou privés.

Several improvements have been introduced for the Fourier modal method in the last fifteen years. Among those, the formulation of the correct factorization rules and adaptive spatial resolution have been crucial steps towards a fast converging scheme, but an application to arbitrary two-dimensional shapes is quite complicated.We present a generalization of the scheme for non-trivial planar geometries using a covariant formulation of Maxwell's equations and a matched coordinate system aligned along the interfaces of the structure that can be easily combined with adaptive spatial resolution. In addition, a symmetric application of Fourier factorization is discussed.

No abstract

A very stable approach for finding optical resonances is to solve an eigenvalue equation that evolves from the linearization of the inverse scattering matrix. In this paper, we show how to use this approach in the Fourier modal method so that advanced coordinate transformation methods such as adaptive spatial resolution and matched coordinates can be included. Furthermore, we present a way that accelerates the computation of the inverse scattering matrix tremendously and allows the derivation of the resonant field distribution inside the structure efficiently.

http://www.jeos.org/index.php/jeos_rp/article/view/07022We present a comparison among several fully-vectorial methods applied to a basic scattering problem governed by the physics of the electromagnetic interaction between subwavelength apertures in a metal film. The modelled structure represents a slit-groove scattering problem in a silver film deposited on a glass substrate. The benchmarked methods, all of which use in-house developed software, include a broad range of fully-vectorial approaches from finite-element methods, volume-integral methods, and finite-difference time domain methods, to various types of modal methods based on different expansion techniques